0
Add your answer:
Earn +20 pts
Where we can install the cooling tower And There is a company in which cooling tower is installed?
The Cooling tower is installed where the continuous heat rejection is required. Like process plants. Type is depends up on use & water property.
What is range in cooling tower?
Range is the difference of cooling water inlet and cooling water outlet temp
Which process used for cooled water in cooling tower?
The process used for cooling water in a cooling tower is evaporation. Hot water is distributed over the fill material in the tower, allowing it to come into contact with air. As the water passes through the fill, some of it evaporates, taking away heat and cooling the remaining water before it is collected and circulated back into the system for cooling.
What is approach of a cooling tower?
Cooling towers are a very important part of many chemical plants. The primary task of a cooling tower is to reject heat into the atmosphere. They represent a relatively inexpensive and dependable means of removing low-grade heat fromcooling water. The make-up water source is used to replenish water lost to evaporation. Hot water fromheat exchangers is sent to the cooling tower. The water exits the cooling tower and is sent back to the exchangers or to other units for further cooling. Cooled water is needed for, for example, air conditioners, manufacturing processes or power generation. A cooling tower is an equipment usedto reduce the temperature of a water stream by extracting heat from water and emitting it tothe atmosphere. Cooling towers make use of evaporation whereby some of the water is evaporated into a moving air stream and subsequently discharged into the atmosphere. As a result, the remainder of the water is cooled down significantly (Figure 1). Cooling towers are able to lower the water temperatures more than devices that use only air to reject heat, like the radiator in a car, and are therefore more cost-effective and energy efficient.
What is wet cooling?
The only thing that I've heard of with "wet cooling" in, is a wet cooling tower. A Wet Cooling tower for the closed-circuit cooling of water where the water to be cooled comes into direct contact with the cooling air dissipating heat by evaporation and air heating. The air draught required for cooling can be induced by fans or by the natural effect of the stack of the cooling tower building (natural draught cooling tower).So I don't know if that answers your question or not, but i hope it helps...
A system that cools the air by spraying water into a tower is called?
The system you are referring to is known as an evaporative cooling tower. It works by using the latent heat of vaporization to cool the air as water is sprayed into the tower and evaporates, absorbing heat in the process.
How much water does a BAC cooling tower hold?
7
What are water treatment paramaters of cooling tower?
Typically this would involve standard titration and colourmetric techniques, which involves analysis and monitoring of the cooling tower.
When the efficiency of wet cooling tower is lower than dry cooling tower?
1. In wet cooling tower Two phase flow heat trasfer 2. To remove sensible heat from water is very critical 3.It depends on water droplet size ,fills design,orientastion and climatical condition. But in dry cooling tower, Air is the only media to remove the heat from the source 1. In wet cooling tower Two phase flow heat trasfer 2. To remove sensible heat from water is very critical 3.It depends on water droplet size ,fills design,orientastion and climatical condition. But in dry cooling tower, Air is the only media to remove the heat from the source 1. In wet cooling tower Two phase flow heat trasfer 2. To remove sensible heat from water is very critical 3.It depends on water droplet size ,fills design,orientastion and climatical condition. But in dry cooling tower, Air is the only media to remove the heat from the source 1. In wet cooling tower Two phase flow heat trasfer 2. To remove sensible heat from water is very critical 3.It depends on water droplet size ,fills design,orientastion and climatical condition. But in dry cooling tower, Air is the only media to remove the heat from the source
If wet bulb temperature is 35 and outlet water temperature from cooling tower is 25 then the cooling tower approach will be effective and what is the solution?
If the wet bulb temperature is 35 and the outlet water temperature from the cooling tower is 25, the approach is effective as the outlet water temperature is 10 degrees lower than the wet bulb temperature. To further improve efficiency, you can optimize the cooling tower's operation by adjusting airflow, water flow rate, and checking for any fouling or scaling in the tower. Regular maintenance and monitoring can also help ensure optimal performance.
How does a cooling tower work?
A cooling tower works by using the process of evaporation to remove heat from a system. Hot water from a heat exchanger is pumped to the top of the tower where it is distributed over the packing material. As the water flows down through the packing, some of it evaporates, which removes heat and cools the remaining water. The cooled water is then recirculated back to the heat exchanger to continue the cooling process.
When the temperature and humidity of air is low you usually use which cooling tower?
natural
