A sump pump discharge line should run as far from the foundation walls as possible.
Possibly the impeller needs cleaning or a blockage in the line
after gate valve, because when you want make maintenance for sump pump , you don't want all water in the pipe drop down sump pump - gate valve - non return valve
It keeps the water that is pumped out from flowing back into the sump when the pump shuts off. Most sumps discharge several feet above the hole the pump sits in. If there was not a check valve the sump would just refill and pump out the water over and over.
air in the line
The sump pump could run continously for 4 different reasons:The switch is bad. The switch is what tells the pump to turn on and off, and it is possible the switch is stuck in the "on" position.The pump is undersized. If the pump is undersized the pump will not be able to keep up with the incoming water and it will continue to run.The pump discharge is restricted. The discharge pipe could be resticted, kinked, or blocked, so confirm there is flow at the end of the discharge.The pump is airbound. A pump gets airbound when the pump looses its prime and is caused by no weep hole on the discharge piping. A check valve has to be in use for this scenario to develop.
If you have any water at all coming into the sump, there will always be a little in the bottom unless it stays dry long enough for it to evaporate. The design of the pump doesn't let it pump the last little bit out. If there is not a check valve in the discharge pipe, what is left it the pipe going out will drain back into the sump. If the discharge pipe is connected to the house drain and there was not a check valve in that pipe, depending on where the kitchen clog is, the sink could drain into the sump.
When you have a crawl space under your home, you have the possibility of having flooding or water build up. If the level of water is allowed to build up too much you can find that your home can sustain costly damage and repair issues. Installing a sump pump in your crawl space can save you from this headache. Here is a guide to help you set up a sump pump for protection. Step 1. Turn off power to the sump pump at the main power source. This will help prevent electrical shock. Step 2. A solid foundation needs to be constructed for the sump pump to rest on. This foundation is best constructed of cinder bocks or a solid piece of wood that is a little larger than the size of the pump. The foundation also needs to be level for the best results. Step 3. Drill a small hole in the discharge pipe. This will help the air flow easier through the pipe for better pressure. Install the discharge pipe from the sump pump to the area where you want to drain the excess water to. Step 4. If water begins to flow back into the sump pump, you will need to install a check flow valve or similar device. Step 5. You will need to attach the power cord for the sump pump to the discharge pipe. This cord must be secure. Step 6. Plug the power cord for the sump pump into the electricity source that you plan on using. Turn the power back on at the main power source for the sump pump to operate. Step 7. It is necessary to test the sump pump for positive operation results prior to using it. To test your sump pump fill the sump pump with water. Never test or operate your sump pump without water being present. Step 8. Add water or refill the pump until there is enough water to reach the level where the sump pump will turn on. Step 9. If you want to install a cover for your sump pump, you can do this now. These covers will help to eliminate dirt and debris from building up in your sump pump and will help to provide odor control from stagnant water.
You would need a sump pump repair if the sump pump in your basement is not pumping out water. The purpose of a sump pump is to drain excess water that is part of your waterproofing system.
its not easy but if you can locate your main drain pipe and its below your basement floor then saw cut up the floor and attach the floor drain to the trap and then tie on to the main line using the same pipe or adapters. If you have no main drain under your basement floor then you will need to saw cut a hole for a sump pump pit or basin and install the sump pump to your main drain line which has to be installed so your sump pump line runs higher then your main line before wyeing to the main line. then cut up the floor to where u want your floor drain and run the drain to your sump pump basin . Some states want a vent on your floor drain and on your sump basin so I would check what your local codes are.
It depends on the power requirements of the sump pump. For a typical residential sump pump, a 2000 watt inverter should be enough. However, it's important to check the power consumption of your specific sump pump to ensure the inverter can handle it.
Your sump pump should have come with an installation guide or CD. If not, contact the manufacturer. Every sump pump is installed differently so you want to make sure you know how to install the sump pump you purchased.