0
Add your answer:
Earn +20 pts
What happens if you shut water off at the meter?
You have shut off all the water to a residence.
What will happen if the main water pipes break?
Water will run until a valve or pump is shut off upstream from water main break.
What does downstream from the valve mean in plumbing?
from the valve past, fowing in the direction of the liquid or gas. example: water supply coming from the street to your house, enters your house where your main water shut off is. then the water is distributed through your house to different fixtures. downstream of your main shut off would be everything past that valve in the direction the water is flowing, or all water lines IN your house.
If the water is turned off at water meter will hot water tank burn up?
Not normally - without the water flowing from the meter, water cannot be consumed within the home, so the level inside the water heater will remain as it was before the water meter was turned off. It is common sense to remove power or shut off the gas to the water heater when another utility is shut down.
Shower off water still on what you do?
Showers and tubs do not usually have shut off valves on the supply lines. To shut the water off you will have to shut off the main water line. There should be one on the cold water line to the water heater. This may shut both the hot and cold off or just the hot. There will be one in the main line coming into the house on the basement wall closest to the street or at the water meter.
Can you wire two oxygen sensors to the same wires to get rid of my check engine light?
NO, you cannot do this, this will compound your problem and eventually damage the engine and/or catalytic converter to the point that they/it must be replaced, all three failures are very expensive repairs. The faulty O2 sensor must be identified and replaced. There are 4 set-ups: Single sensor; Dual "upstream" <both sensors are pre-cat>; Dual upstream/downstream <one sensor is pre-cat, one sensor is post-cat> and Quad sensor <two sensors are pre-cat, two sensors are post-cat>. The upstream controls the fuel mixture and the downstream monitors the catalytic converter. BANK 1 is always the number 1 spark plug side and SENSOR 1 is always upstream. Once the fault is corrected the ECM must be cleared with a scanner to shut off the light.
How to shut off the water to the house?
Call your local utility (water company, for example) as the shutoff valve will most likely not be right at your property line. In the meantime, enjoy the cool water.
How do you change a shut off valve?
I'm not being stupid, you just change it. How ever it is installed, threaded on, sweated or compression fitting, remove and replace. I'm assuming water. There is another shut off valve further down the line. If it is the main shut off in the house, there is one at the meter. Shut the water off, drain the pipes and change it.
How do you determine if an outlet is after or before the gfci?
You can determine if an outlet is after a GFCI by pressing the "test" button on the GFCI outlet. If the GFCI trips and cuts off power to the outlet, then that outlet is downstream from the GFCI. If power is not cut off, then that outlet is upstream from the GFCI.
WHERE ARE THE SHUT-OFF VALVES IN A DALLAS HOME?
Whenever you want to do plumbing repairs in Dallas, whether it is to change a leaky faucet or fix knocking pipes, you need to know how to shut off the main water line, or supply. But, most homeowners do not know where their main shutoff valves are, especially if they have just moved in or are renting a home that is unfamiliar to them. The water meter, which you can usually find in your basement or just outside your home, will have a shutoff valve attached directly to it. Usually, there will be two shutoff valves – one on each side of the meter (supply and home). To effectively shut off your water supply, turn the valve located before the meter. If you need help replacing your main water shut-off valve, our Dallas plumbers can help with that too! To help, here are some common places you can look for shutoff valves in your home and how to shut off water to a house in Texas.
How do you safely remove a watt meter when the meter socket is energized?
First, shut off all power to your house.
Do you need to shut off hot water heater when replacing copper pipes in a bathroom?
Yes you need to shut off the Main water valve. Usually found in the basement or outside the house near the meter. Also you need to shut off the Gas valve located at the water heater, or the Breaker located in the breaker box/ fuse panel. Sometimes the water heater will have its own Switch box, located on the power wire
