0
Considering the waste inlet of the pipe of this pipe should be 4" possibly 3" you can buy an inside cast iron cutter .=You must measure the inside diameter and then buy /rent the one for the size you need THEN you can buy a new cast iron floor flange and use either a caulked joint (lead and oakum) or possibly a quick set type if the cast iron is no hub or standard weight=
Add your answer:
Earn +20 pts
Does the toilet flange go on the inside or outside of soil pipe?
Toilet flanges OUTSIDE of the pipe including cast iron and brass to lead
Your toilet flange broke how do you replace it?
Depends on the type what means I use to replace it CAST Iron/ BRASS / Antimony / PVC / SCREWED TYPE
How do you install a regular toilet flange on a cast iron 6 inch sewer pipe?
If you can get to the 6 inch cast iron, you could use a rubber coupler between the cast and the flange. If it is in the concrete, put a piece of 4 inch PVC inside the 6 inch and lead it in like you would a regular cast joint. Leave the 4 inch above the floor and slide the flange over it, screw it down and cut the 4 inch flush with the flange. They make just the flange that will slide over the pipe.
How to repair closet flange?
Cast iron, often break where the bolts sit. There is a repair kit available. It is two flat curved pieces of metal about 3/4 wide and one third the circumference of the flange. It slides under the flange and pulls against the remaining cast iron. There is a complete ring available that is just a flat ring with 6 ears sticking out around the edge that should clear the cast iron. Screw it down to the floor and install the toilet. The full ring can be used with any flange.
How do you repair toilet bowl mounting flange?
depending on your type of flange and pipe and the damage of the flange, if you have a PVC flange with just the bolt slots busted then you can screw in new bolts to the floor below the flange and still use the flange but if its broken where the wax seal sits then if your flange is lower then the floor you can use a insert flange that fits inside your old toilet flange with thin walls to keep the pipe size maximum. To replace the entire flange can be a job especially if its in concrete or in a floor joist because most of the time you have no room and if its cast iron pipe it can be even more of headache but in order to replace the flange you need to cut it out to where you can reconnect the pipe and flange by using a fernco or a no hub band. Sometimes it is impossible to replace because the flange can be on all close fittings and you pretty much have to replace most of the plumbing drain pipe to replace it properly which is why you want to try repairing your toilet flange rather then replacing it .
What is the best way to move the toilet flange a couple of feet and is there an adapter to go from cast iron to PVC?
Cut the toilet line down at the first 90 from the flange, and relocate so that your toilet is still vented from it's orignal vent. If it is dry vented, you need to move the toilet and the vent. A no-hub band or fernco coupling is the preferred transistion from cast iron to PVC.Ans 2 -good advice. - BTW, - a Fernco is a heavy duty rubber coupling with a hose clamp each end. They come in many sizes.
How do you install a cast iron flange on a cast iron pipe?
You can buy the new cast iron flanges, with the expandable O rings that push into the pipe or you'll have to do the old style or pouring lead onto a cast iron flange. The latter option should only be done by professionals.
How do you replace cast iron flange?
You have to take the lead and packing out that is holding the flange in the next piece of pipe. If your flange is broke where the toilet bolts go, this is very common. There is a repair available for this. It consists of two curved pieces of metal that are about 1/3 of the circumference of the flange. They go under the flange and give you a new place to put the bolt. They are a lot easier to use than replacing the whole flange.
How do you replace a broken cast iron toilet flange?
If you are a do it yourselfer, there are many adapters available to replace a broken cast-iron toilet flange. These adapters can be made of cast-iron itself or PVC. They are made to be inserted into the existing pipe where a rubber gasket is tightened to create a water tight seal. The adapter incorporates a new flange which is attached to the existing sub-floor. Other adapters even help in the case of damaged or rotten sub-floor around the waste pipe. If you do a search on "Repair Kit For Cast-Iron Closet Flange" you should come up with numerous options or you can visit your local pluming supply company who can provide you with both products and answers to any questions/concerns you might have. And if you don't feel comfortable doing this yourself after investigating what is involved, call a licensed plumber.
Need new toilet flange?
Or repair what you have. Cast iron broke where the bolt goes. There is a steel half moon piece available that slips under the lip of the cast iron and bridges the broken out place. There is a brass ring available that screws down over the drain. It comes in a flat steel ring also.
If you have a 4 cast iron stack with a 4 outlet to the toilet and the pipe coming up to the toilet is lead how do you attach a toilet flange to this 4 lead pipe?
The flange is actually a ring that the lead comes up through the middle of. The ring is secured to the floor and the lead is beat down against the flange. T would actually consider doing away with this lead bend as they are currently 50 years old or older. That is to say they stopped using them about 50 years ago and they are currently failing in a lot of homes. I w3ould cut the lead out leaving the brass stub in the cast iron where the lead attached, and repipe with PVC to that brass stub and attatch it with a fernco coupling. Three inch PVC will slide right inside that brass stub to make a real nice connection,Answerif you have the pipe flush with the finish floor you can get a plastic flange with a rubber ty seal gasket around it. this will fit inside the 4" pipe. or if the lead is exposed you can snap it at the cast iron and transition to plastic.
How do you connect commode to sewer line?
Floor flange, cast iron ,brass with floor flange bolts (brass) wax gasket and make sure the line is vented
