0
Well what sort of application is the 2600 router going to be used in? Here is a short thing about setting the clock http://www.learnios.com/viewtopic.php?f=4&t=36 Here a little more on setting up interfaces http://www.learnios.com/viewtopic.php?f=72&t=34 Here is password recovery steps http://www.learnios.com/viewtopic.php?f=4&t=28 Setting up Cisco routers can be done many ways if you are looking for and more direct answer I suggest asking a more direct question like "how do I setup DCHP on my 2600" or how do I ip interfaces
You could use a roll-over cable to connect to the console port of the cisco router and login to the router through Hyper Terminal
I think all cisco 1800 series routers use "cisco" as username and password by default
If u'r not comfortable with cisco commands I would recommend using SDM (Security Device Manager) software to configure the router.
You can download the CISCO SDM from the cisco web site, it's free of charge.
Install the SDM in u'r windows PC and connect to the router.
With this method you could configure the router in a GUI environment.
There are many, many different things you may need to configure - much more than I can explain here in a few paragraphs. Better take a Cisco CCNA course, or look for configuration examples at www.cisco.com.
In the simplest case, you will enable interfaces (ports), and configure their IP addresses. But you may also have to configure some other things, for example:
- NAT translation.
- A routing protocol, such as RIP, OSPF, etc. - this allows the router to share routes with other routers.
- Static routes are also used in some cases.
- Special configuration commands for frame relay, ISDN, or other WAN technologies.
- Passwords, to protect your router from unauthorized access.
Add your answer:
Earn +20 pts
At Which Prompt would you configure the Hostname on a Cisco Router?
You can do this on the enable, or privileged, prompt.
What mode must be in to configure IP address on a Cisco router?
interface mode
Which command sequence will permit access to five router virtual terminal lines with a password of cisco?
router>enable router#configure terminal router(config)#line vty 0 4 router(config-line)#password cisco router(config-line)#login to configure router with telnet you must set up password or secret for privilieged mode.
How do you connect a router to cisco 1800?
To connect to a cisco 1800 series router, you need either a network connection that goes to the router, and then you would configure the router to allow telnet or you would need a console cable, also called a rollover or cisco cable and physical access to the device.
What are the hyper terminal settings to allow configure a cisco router?
9600 8-N-1
How can configure isdn in cisco router?
Changing the username and password that a Cisco ISDN router uses to dial-up ... in the router configuration in encrypted format, so even if you canview the settings. By lutaaya sulaiman +256753302061; lutasula@yahoo.com
What router prompt can you use the router rip command?
On a cisco router you would go into privilege-exec mode (enable) and then into "configure terminal" mode. From there you can use the router rip command.
What is setup mode?
When a Cisco router is booted up for the first time, or is reloaded, the router will look into its Non-Volatile RAM (NVRAM) for the startup configuration file. Setup Mode is usedto configure a Cisco router or switch after start up to create a startup configuration file.
You've just received a new Cisco router for your data center and it came with a roll over cable What can you do with this cable?
make a connection from the router's console port to your laptop's serial port and configure the router from your laptop.
Static route when multiple routes need to be configured?
You can configure multiple static routes. On a Cisco router, you would give several ip route commands. However, if there are a lot of routes to configure, it is more practical to use a routing protocol - that way, the routers learn available routes automatically.You can configure multiple static routes. On a Cisco router, you would give several ip route commands. However, if there are a lot of routes to configure, it is more practical to use a routing protocol - that way, the routers learn available routes automatically.You can configure multiple static routes. On a Cisco router, you would give several ip route commands. However, if there are a lot of routes to configure, it is more practical to use a routing protocol - that way, the routers learn available routes automatically.You can configure multiple static routes. On a Cisco router, you would give several ip route commands. However, if there are a lot of routes to configure, it is more practical to use a routing protocol - that way, the routers learn available routes automatically.
How do you connect two different LAN with a single Cisco router?
Configure two interfaces, and build the routing table accordingly with their private IPS.
When does the banner display for cisco router?
whenever you log into your cisco router....
