0
Add your answer:
Earn +20 pts
Will adding a second submersible pump of the same size using a Y coupling increase the flow in a 2 inch discharge pipe with a head of 25 feet?
The 2" pipe will only handle so much water and no more. Even an 8 horse power pump will not increase the flow in a 2" pipe. 2" plumbing has only a certain capacity and no more.
Will a 2 hp Franklin submersible well pump motor fit a 1.5 pump?
There is no such thing as a 1.5 pump. - Pumps are rated in gpm and inches. If the pump end is 4" , it will fit any 4 " Franklin motor.
If i have an 1 2 inch pipe and want to cap it would i buy a 3 4 inch cap or 1 2 inch?
1/2 inch for 1/2 inch pipe.
What are the key features and specifications of a 2hp submersible pump?
A 2hp submersible pump typically has a power rating of 2 horsepower, allowing it to efficiently pump water from underground sources. It is designed to be submerged in water, making it suitable for applications such as well pumping and drainage. These pumps are usually made of durable materials like stainless steel and have a maximum flow rate and head pressure that can vary depending on the specific model.
Does a 110 submersible well pump need a pump start?
If it's a '2 wire pump' the starter is inside it. That has black, red and ground wires. (yes I KNOW that's 3 wires, but it's called a 2 wire pump). If it is a '3 wire pump' and has black, red, yellow and ground then it needs a 'pump control box' (starter and o/l switch) somewhere near the pressure tank.
What is a Myers Ejecto well pump?
It is what is commonly called a "Jet Pump". This is a motor connected to a pump chamber that has 2 pipes going down the well and sucks water through an 'ejector' that increases flow and brings water to the surface. This pump sits at or near the well head. - The other basic type of well pump is a "Submersible" pump. These sit down the well, deep in water and pump straight to the surface through a series of impellers.
Where is Fuel pump location 1993 Isuzu trooper?
inside the fuel tank..... isn't very hard to drain it and remove the tank to get at it.... I bought the 2 inch cheaper pump since it was rated the same as a 1 inch
What is wattage of half hp water submersible pump?
at least 1500 watts, 1horse power is 746 watts, therefore 1/2 horsepower is 373 watts. But the answer will depend on the %age efficiency of the motor in the pump. Assuming an efficiency of 50% 746 watts would be an appropriate answer.
Can shotguns chambered for 3 inch shells also shoot 2 and three quarter inch in a browning bps 20 gauge pump shotgun?
yes.
What will make the overload switch off on a Goulds 112 hp deep well pump with all new wire circuit breaker and know to be good pump?
A complete answer requires more information. A 112 hp pump is a non-standard size. It's also huge - large enough that it would not be used by a person who needs to ask the question. There is no model number to indicate whether it's a submersible pump or a two-pipe deep well jet pump. If I had to guess, it's likely the pump is only 1/2 hp. Submersible pumps of this size are commonly available either with a controller (3-wire) or without a controller (2-wire). In addition, both configurations may be rated for either 115 or 230 volts. Selecting the wrong controller or failing to install a controller where required will cause the overload to trip. Virtually all jet and submersible pumps use a start capacitor connected to a start switch or relay. If either component is missing or failed it will also trip the overload.
What is a good online source to buy 2 to 3 inch hollow plastic balls?
You can buy 2 to 3 inch hollow plastic balls at www.complexplastics.com/BALLS/balls3of3.htm. Another good website is www.complast.com/balls/
How much does it cost to replace a sub pump?
A 'sub pump' is the shortened term for a 'submersible pump' as used in a domestic deep well. ( first, dispel ANY notion that this is a 'sump pump ! -NO similarity whatever. ) -Sub pumps come in many forms depending on how deep they operate and how much water they must pump. Most domestic submersible pumps in north America are 1/2 or 3/4 hp electric motors turning a tiered, vaned pump. They commonly operate between 100 and 400 feet deep and pump 5 - 15 gallons per minute to the surface. These domestic pumps are like a silver cylinder, 4 inches in diameter, about 2-4 feet long. ( - THERE ARE many variations, and I have personally worked on pumps for meat plants that are a foot wide and 10 feet long ) The cost of installing a domestic sub pump depends on what pump model and how deep it is. Pump tube and wire cost about $2 per foot. An average pump will cost 400 -700. - - The questioner has not given enough detail for a definitive answer.
