answersLogoWhite

0


Best Answer

An impeller is a rotor used to increase the pressure and flow of a fluid whereas a propeller is a type of fan that produces thrust by moving air or water. In general, impellers are found in pumps and compressors, while propellers are commonly used in boats and aircraft.

User Avatar

AnswerBot

5mo ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the difference betwee impeller and propeler?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Physics

Axial load in impeller?

Axial load in an impeller is the force acting along the axis of rotation, causing a pushing or pulling effect. It is important to consider the axial load in impeller design to ensure proper functioning and structural integrity. Balancing axial forces is critical to prevent shaft deflection, bearing wear, and potential failure of the impeller system.


Relation between impeller width and its speed?

Increasing impeller width typically results in increased flow capacity and efficiency at a given speed as it can accommodate more fluid. However, wider impellers may require higher speeds to maintain proper velocity and prevent recirculation effects. It is important to consider the trade-offs between impeller width, speed, and the specific requirements of the application to optimize performance.


What is centrifugal force in pumps?

Centrifugal force in pumps is the force generated by the spinning motion of an impeller inside the pump. This force is responsible for creating a pressure difference that pushes the fluid towards the outlet of the pump, allowing for the transfer of the fluid from the inlet to the outlet.


What is the difference between an agitator and an impeller in a washing machine?

Top-loaders have two options for swirling the load: an agitator (central spindle), or an impeller (a small bump at the bottom of the bowl). Impellers spin and pulse to turn the washing over, rather than twisting it. Washing machines with impellers tend to be easier to load and unload, but their dirt removal isn't always as good as agitator models.


What is the difference between two phase and double sampling?

Two-phase sampling involves selecting initial units from a population through one sampling technique and subsequently selecting final units from the initially drawn units using a different sampling technique. Double sampling, on the other hand, involves selecting two independent samples from the same population, where the second sample is used to check the results of the first sample and make adjustments if needed.

Related questions

Meaning and use of propeler anemometer?

meaning and use of propeler anemometer


What is the major difference betwee vcb and acb?

vcb and acb


Difference betwee nymex crude and brent crude?

Difference between nymex crude and brent crude


What is the difference between a propeller and impeller?

Propeller is external (outboard motor on a boat) Impeller is internal (vehicle water pump).


How do you get a propeler hat on cp?

u can get in in the tresuare book


The circulation of water in the ocean due to difference in density betwee the different layers of water is mostly responsible for?

somethin


How does helicopter's work?

the engine inside causes the propeler to spin


How do you float on Club Penguin?

you just get a propeler's hat and dance


What is difference between 2.5 percent and 2.50 percent?

There isno differe nce betwee n 2.5% a nd 2.50%. They are the same.


Difference between compressor and pump rotor?

The only one difference in b/w compressor and pump rotor is impeller shroud width.Fluid is incompressible so impeller shroud width is not change and gas is compressible so impellers are tends to thin in width to the discharge side.


What is the difference betwee a bird and an aligator?

The difference is an aligator is a reptile and a bird is not. Also aligators can weigh up to a ton or more and usually birds die if they do. And also aligators have teeth and birds do not.


Axial load in impeller?

Axial load in an impeller is the force acting along the axis of rotation, causing a pushing or pulling effect. It is important to consider the axial load in impeller design to ensure proper functioning and structural integrity. Balancing axial forces is critical to prevent shaft deflection, bearing wear, and potential failure of the impeller system.