0
During the sulphated ash test, constant weight refers to achieving a stable mass of the sample after it has been ignited to remove any organic material and drive off volatile substances. This step ensures that all organic components have been effectively burned off, leaving behind only the inorganic residues for accurate measurement. Constant weight indicates that the sample has reached a point where no further change in mass occurs, confirming complete combustion.
Add your answer:
Earn +20 pts
In weight test what is the difference between a static test load and a dynamic test load?
A static test load is applied gradually and held constant to measure the structure's deformation and ultimate load-carrying capacity. On the other hand, a dynamic test load is applied rapidly and repeatedly to simulate real-life conditions and assess the structure's response to dynamic loads such as wind or seismic activity.
Why the speed is kept constant for conducting Morse test?
Maintaining a constant speed during a Morse code test ensures consistency in message delivery and reception. It allows for accurate assessment of the participant's proficiency in interpreting the code without the added variable of speed fluctuations. This standardization helps in comparing results across different tests and individuals.
How would you test an objects weight before attempting to lift it?
You can test an object's weight by using a scale or balance to measure its mass. This will give you an accurate numerical value of the object's weight before attempting to lift it. Alternatively, you can also use your own judgment based on previous experiences with lifting objects of similar size and material to estimate its weight.
How do you calculate air inclusion during hydro test?
To calculate air inclusion during a hydro test, you would measure the volume of air bubbles released during the test using a calibrated container. The volume of air collected can then be compared to the total volume of water used in the test to determine the percentage of air inclusion. This can help assess the integrity of the system being tested.
What is run-time object in qtp?
In QTP (Quick Test Professional), a run-time object refers to an object or control within the application being tested that is identified dynamically during test execution. These objects are identified based on their properties and can change during test execution based on user interactions with the application. QTP uses test objects and test object methods to interact with run-time objects during test execution.
Why used sulfuric acid in sulphated ash test?
Sulfuric acid is used in the sulphated ash test to convert the inorganic components present in the sample to their sulfates. This step helps in ensuring complete combustion of organic material and facilitates the determination of the ash content accurately. The use of sulfuric acid also helps in removing any carbon residues that may be present in the sample.
What is sulphated ash?
The sulphated ash test is an analytical test for determining the inorganic content of a sample by weight. The sample ( usually 1g) is accurately weighed into a platinum, silica crucible that has been previously ignited, cooled and weighed. The sample in the crucible is then subjected to sulphuric acid (usually 1mL) and charred at a low temperature without causing ignition of the sample until there are no more white fumes given off. The crucible with the charred sample is then placed in a furnace (temperature is dependent on monograph but typically it can be from 600 to 900 degrees celcius) until all organic matter has been burnt off. The crucible is cooled and re-weighed. The difference in sample weights being the sulphated ash content remaining. Some monographs require the sample to be re-ashed until a constand weight has been achieved. The remaining inorganic matter is typically metal oxides from most samples.
Why does the tensile test curve decrease after a maximum load is obtained?
because the cross-sectional area decreases as the test progresses. to keep the pressure constant, the weight must decrease. (pressure is force divided by area)
Full form of CPS?
Constant Pressure Test
Examples of constant variables in flame test?
The temperature of the flame.
Weight gain before a pregnancy test will show if pregnant or not?
If you have gained weight or not have nothing to do with it. If you are pregnant the test will show.
In weight test what is the difference between a static test load and a dynamic test load?
A static test load is applied gradually and held constant to measure the structure's deformation and ultimate load-carrying capacity. On the other hand, a dynamic test load is applied rapidly and repeatedly to simulate real-life conditions and assess the structure's response to dynamic loads such as wind or seismic activity.
Gestational Diabetes Symptoms?
Gestational diabetes symptoms include being tired during pregnancy, rapid weight gain and a positive glucose test.
How do you prevent passing out during a blood test?
Request to lie down during blood test.
When z test is used?
The term Z-test is often used to refer specifically to the one-sample location test comparing the mean of a set of measurements to a given constant.
Which factor needs to stay constant to test Boyle's Law?
The amount of gas and its temperature.
Are constant hiccups and backaches a sign that I am pregnant?
Can be. Wait until your period is late and do a test.
