0
These devices contribute to the energy-wasting phenomenon called "phantom power," or vampire energy. Simply put, this is the power that is used when electronic devices draw energy from the grid into your home just by being plugged in, when you aren't looking and you aren't using them.
Many electronic devices continue to draw power even when not in use. Energy drawn by the standby mode sometimes is referred to as a "phantom load." An estimated 50 percent of the energy used by an electronic device is drawn while the device is not in use, making phantom loads responsible for 4 to 7 percent of your total electricity use. Phantom loads can be reduced in many ways, some of them for little cost or free.
Still curious? Ask our experts.
Chat with our AI personalities
Vivi
Maxine
SteveDirect loading of an energy meter involves connecting the load directly to the energy meter without the use of external Transformers or current transformers. This method is typically used for smaller loads that do not require high accuracy readings. It simplifies the installation process, but may result in decreased accuracy compared to using external transformers.
Energy Meter or Watt-Hour Meter is an electrical instrument that measures the amount of electrical energy or energy used by the consumers over an interval of time.
The basic unit of power is watts and it is measured by using a watt meter. One thousand watts make one kilowatt. If one uses one kilowatt in one-hour duration, one unit of energy gets consumed. So energy meters measure the rapid voltage and currents, calculate their product and give instantaneous power. This power is integrated over a time interval, which gives the energy utilized over that time period
3-Phase Energy Meter is used for measuring the power of three phase supply, It can interface with different services like 3-phase 4-wire, 3-phase 3-wire, and 3-phase 4-wire with 2½ elements. It can also provide active, reactive, and apparent energy calculations as well as power quality measurements, voltage rms, and current rms. The 3-phase meter is constructed by connecting the two single phase meter through the shaft. The total energy is the sum of the reading of both the elements.
Utilities are one of the electrical departments, which install these instruments at every place like homes, industries, organizations, commercial buildings to charge for the electricity consumption by loads such as lights, fans, refrigerator, and other home appliances.
Standard used for Calibration of Energy Meter:
The calibration laboratory is accredited by NABL as per ISO/IEC 17025:2017 standard.
Comparison method using 3-Phase Energy Meter, Electrical Source.
Calibration Parameter of Energy Meter: AC Voltage, AC Current, AC Power – Active Power Reactive Power, Power Factor, AC Active Energy, AC Reactive Energy.
Some of Calibration Laboratory:
• NPL - The CSIR- National Physical Laboratory of India, situated in New Delhi, is the measurement standards laboratory of India. It maintains standards of SI units in India and calibrates the national standards of weights and measures
Contact Address: New Delhi – 110012
Phone (Reception): 011-45609212
• MSME - The Ministry of Micro, Small and Medium Enterprises, a branch of the Government of India
Contact Address: Guindy, Chennai
Phone (Reception): 044-22500539
• ETDC - Electronics Test & Development Centre, Chennai is a premier Government of India organization, with specialization in comprehensive testing of Electronics and IT products as per National Standards of Bureau of Indian Standards (BIS) and International Standards like International Electro-technical Commission (IEC) as well as other industrial and company standards
Contact Address: VSI Estate, Thiruvanmiyur, Chennai - 600 041
Phone (Reception): 044-24547700
• CPRI - Central Power Research Institute, CPRI is the power house of the Indian electrical industry. Set up in 1960 by the Government of India, it functions as a centre for applied research in electrical power engineering assisting the electrical industry in product development and quality assurance.
Contact Address: 4th Block, Dodda Basti, Sir M Vishweshwaraiah Layout 4th Block, SMV Layout, Bengaluru, Karnataka 560056 Bangalore
Phone: 080-22072213
• Godrej Calibration Services – a division of “Godrej & Boyce Mfg Co Ltd”,
NABL accredited calibration laboratory as per standard ISO/IEC17025:2017. They are world class and well equipped laboratories who delivers calibration services of the highest quality and ensures services by maintaining your instrument at highest accuracy level.
Godrej Calibration Services is one of the largest private labs in India, Calibration Labs at Mumbai, Pune, Vadodara, Chennai, Gurugram, and Regional offices in Bhopal, Bangalore, Hyderabad, Vizag.
Over 15000+ Customers in India, Bangladesh and Middle East for Onsite and In-house calibration as per customer requirements.
Contact Address:
Chennai: No.1 Sidco Industrial Estate, Ambattur, Chennai-600098, Tamilnadu, India. Phone (Reception): 044-66544651/52/53.
Mumbai: Plant 18B, 1st Floor, Godrej Compound, Pirojshanagar, Vikhroli East, Mumbai-400079, Maharashtra, India. Phone (Reception): 022-67965914/18/76.
Add your answer:
Earn +20 pts
What is the difference between direct loading and phantom loading?
Direct loading involves connecting a constant power source to the load, while phantom loading involves electrical devices drawing standby power even when turned off. Direct loading consumes power only when the load is active, while phantom loading results in wasted energy consumption.
What is the mechanical wave of a direct measure of it's energy?
The mechanical wave's energy can be directly measured using instruments like a power meter or a calorimeter. These devices can quantify the wave's energy by measuring the amount of work done by the wave as it travels through a medium.
How will you define energy meter constant?
The energy meter constant is a value that is used to convert the reading from the energy meter (in watt-hours) to the actual energy consumption of a device or system. It is typically a fixed value that is specific to the energy meter being used and is determined during the calibration process.
Which si unit for energy is also called thwe newton meter?
The SI unit for energy that is also called the newton meter is the joule (J).
How is Energy transferred to a light meter?
Energy is transferred to a light meter through the incident light that falls on its sensor. The sensor then converts the light energy into an electrical signal that is proportional to the intensity of the light. This electrical signal is used to determine the light level and provide a reading on the light meter.
