answersLogoWhite

0


Best Answer

5 1/2 in the doors, and 5x7 in the back

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What size is 1990 Plymouth sundance speakers?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Performing Arts

1992 Plymouth sundance gas tank size?

it has a 16.4 Gallon tank. how i know is i have a 93 sundance and it was on empty and i put 10 in gas it gave me 4.100 gallons and put me on a quarter of a tank so 4.100 times 4 qaurters tank of gas =16.4 Gallons


Where to place speakers in home theater?

This depends on what speakers you have, the size and shape of the room, and a little personal preference. Generally, evenly placed encircling the room, then subwoofers or larger speakers in the back or sides and the rest put around the room in open spaces


What are the best 5.1 computer speakers for someone with a rectangular room 14x7ft and a 400 budget?

The size of the room doesn't matter so much - as where you position the speakers. For maximum effect, the user should be sat centrally in the room, with the main unit facing them from underneath the computer. The four 'satellite' speakers should be in each corner of the room.


How do you wire stereo speakers?

The new speakers come with un-stripped copper wires..... you need a pair of wire strippers.... i put in kenwood speakers and the size of the wire was 14 somethin. you would need to get a wire diagram for you car/truck to see the colors of the positive and negative wires. then look on the aftermarket speaker box to see which wire is negative and which one is positive.... After you would do all this, just match up negative to negative and positive to positive. simple as that. I'd recommend wire nutting the wires or electrical taping them... but DO NOT put all four wires together. that will mess your speakers' sound up completely. wire nut the positives together and then wire nut the negatives together.


What size audio amplifier will you need to buy to power four 60 watts speakers 8 ohms impedance Frequency Response 120 Hz - 20 kHz?

There are several ways to drive four speakers. For simplicity, this answer assumes that the amplifier will be a two channel stereo amplifier - one channel for left and one for right hand channels. It also assumes that the speakers will be connected in parallel, that is, both positive terminals wired together and both negative terminals together. The two speakers together will be the equivalent of a four ohm speaker. First, make sure the amplifier is rated to drive four ohms to both the left and the right speaker. Most amplifiers will handle a four ohm load but some are aonly designed for eight ohms. The manual will tell you what the amplifier can handle. The speakers can handle up to 120 Watts per channel when two are used together. To fully drive the speakers, an amplifier of 120W per channel will be needed. However, that is the worst possible size of amplifier to use if you are going to run the system near its peak power output. Here's why: Speakers are able to cope much more power than their rated power. The sound will be terrible but generally, the speakers will not be damaged. Speakers can also cope with a distorted signal from an amplifier as long as the power level is a lot less than the rated speaker power. However, overdrive the amplifier when it is delivering the full power rating of the speaker and the high power distortion is very likely to cause damage to the speaker. The choice of amplifier should either be higher or lower than the speaker rating. A 30W per channel amplifier will still have a great deal of power to offer and the output will be far louder than most people would ever want in a living room. If the amplifier is over-driven, the low power level avoid speaker damage. A 200W per channel amplifier will drive the speakers harder but with a clean signal. If you want to run the speakers close to their maximum level, choose an amplifier of this power output or higher. A note about power levels: True power output is always measured as an RMS figure. Music power is approximately twice RMS power and peak music power is about twice the level of music power. Therefore, if the speakers are rated at 60W peak music power, they actually have a rating of just 15 Watts RMS. When comparing amplifiers and speakers, always make sure you use the same units, RMS, Music or Peak Music. Never mix them.