0
Add your answer:
Earn +20 pts
What should you do if you are exposed to natural gas?
If you are exposed to natural gas, leave the area immediately and go outside to fresh air. Do not use any electronic devices or lighters, as these can ignite the gas. Contact your gas company or emergency services for assistance.
What does the flame in a gas cooker go out when you turn the gas off?
The flame goes out because you turned it off.
How do you turn on your natural gas at the meter?
You can't miss the shut off valve on the main line close to the pressure reg just before the meter.Should have a hole in it and behind it is another hole, this is so it can be locked by your power company. If the holes match it is off,rotate it 45deg or in line with the pipe. Everything on this planet for a valve is on when in line with the flow of pipe and when its at a right angle to pipe it is off.
How do you turn off the Bunsen burner?
To turn off a Bunsen burner, first close the air hole at the base of the burner by turning the metal collar clockwise until it's fully closed. Then turn the gas knob on the burner clockwise until it stops to shut off the gas supply. Let the burner cool down before handling it.
Gas fireplace wont stay on I have a FMI model GL-6100 gas fireplace when I turn it on after 2 or 3 min it shut down Evan the pilot lite goes out I hear a pop sound that seem to come gas value?
It sounds like there may be an issue with the gas valve or thermocouple in your fireplace. The pop sound you hear could indicate a problem with the gas flow. I recommend contacting a professional technician to inspect and repair the issue for safety reasons.
What is a gas assist fireplace?
A woodburning fireplace with a gas burner. Load it with firewood, and light the gas burner to get it started, When burning well, turn off the gas.
How do you convert a wood burning fireplace into a gas fireplace?
first off you need to turn off the gas then, cap the gas line then remove the gas line and the vent pipes up in the chimney, then remove the insert or gas log, then install damper doors, put on a suitable door to the fireplace, and put a basket in the fireplace to hold the wood The above paragraph assumes that the fireplace was originally a wood burning fireplace that was retrofit to accommodate a gas fireplace insert and in that circumstance the information is accurate. However, if the fireplace was originally designed as a gas appliance it cannot be converted to solid fuel ( wood ).
Can a gas log fireplace be changed over to wood fireplace?
First off you need to turn off the gas and cap the gas line. Next, remove the gas line and the vent pipes up in the chimney. After that, remove the insert or gas log and install damper doors. Then, put on a suitable door to the fireplace. Finally, put a basket in the fireplace to hold the wood.http://wiki.answers.com/How_do_you_convert_a_gas_fireplace_into_a_wood_burning_fireplace#ixzz17W5OFp8M
Does rotating a gas valve on an indoor fireplace counterclockwise open or close the gas line?
All gas fireplaces have to have a shut-off valve within 10' and that will turn so the key or the handle is parallel to leave gas on and perpendicular to turn gas off. The valve inside the fireplace turns but not indiscriminately. The inner valve will turn to the pilot setting and depress to light the pilot. Once the pilot os stable the knob will un-depress and turn to the On position. For a manual valve this will turn on the gas flow to the main burners. If using a switch or remote turning the valve to On leaves the fireplace valve in a Ready position so the switch or remote will turn on the gas.
How do you replace a thermocouple on a gas fireplace?
To replace a thermocouple on a gas fireplace, first turn off the gas supply and wait for the fireplace to cool down. Locate the thermocouple near the pilot light and unscrew the old one from the gas line, then install the new thermocouple by screwing it in place and reassemble the gas line. Finally, relight the pilot light and test the fireplace to ensure the new thermocouple is working properly.
Why do the flames on my gas fireplace not turn up?
The reason why the flames on your gas fireplace do not turn up could be because the gas valve is not turned up high enough. Another problem could be that the holes on the main burner are clogged up, in which case you can clean them with a stiff brush once you have turned off the gas at the mains supply.
What can be causing the gas fireplace to have a strong gas odor?
A strong gas odor coming from a gas fireplace is likely due to a gas leak. This can be caused by a malfunctioning pilot light, loose connections, or a faulty gas valve. It's important to immediately turn off the gas supply to the fireplace, ventilate the area, and contact a professional to inspect and repair the issue to prevent any safety hazards.
how do I clean my gas fireplace?
Turn off the gas and electric. Remove all the items like log and burner. Turn off the pilot lite and use a dry cloth to wipe it down when cool. Clear the vents and clean the glass with an ammonia based cleaner.
What cures a gas fireplace making a loud bang after turning it off?
A loud bang in a gas fireplace after turning it off could be caused by excess gas in the combustion chamber igniting when the fireplace shuts off. To fix this issue, you should have a professional inspect and service the fireplace to correct any gas flow problems or issues with the ignition system. It is important to address this problem promptly to prevent safety hazards.
Can you light your pilot on your gas fire fireplace when your gas says off?
Maybe. Get the instuction manual for your fireplace. Depends on whether the OFF is master valve, or secondary valve. If no manual, hire a gas service company to do it, and show you how.
Should you turn off the propane gas tank when turning off the pilot on your gas fireplace?
There is no reason why you MUST turn off the tank as well, but if the only appliance supplied by the tank is being turned off for an extended period of time, turning off the tank would be another safety percaution....(lightning strike, break in the line).
How can you compute the natural gas consumption of your fireplace?
Turn off all of the gas appliances in the home except for the the fireplace. Watch the gas meter for 60 seconds and record the cubic foot usage, multiply the reading you get times 60 and that is your NG consumption for 1 hour. To convert to btu, multiply the 1 hour reading by 1000 and that #, if the fireplace is set up and burning properly should be the same as the Input rating on the fireplace tag. If you simply want to know how much gas you are using when lit, divide the Input rating on the tag by 1000 and that will tell how much NG you are using per hour in cubic feet.
