The equation for wattage is W = A x V. Substitute your values into this equation and you will have your answer.
The measure of the electric power an appliance uses is called wattage. It is typically expressed in watts on the appliance's label or specifications. The wattage helps determine the energy consumption and cost of operating the appliance.
Amps (current) times volts = watts. so watts divided by volts = current (Amps). i.e.- 0.5 Amps.
To calculate amperage, use the formula: Amperage = Wattage / Voltage. For a household appliance with a wattage of 720 and a standard voltage of 120 volts, the amperage would be 6 amps. (720 watts / 120 volts = 6 amps).
Yes, you can use a 1000 watts transformer with a 700 watts appliance. The transformer's capacity should be equal to or greater than the appliance's wattage to prevent overloading or damage. In this case, the 1000 watts transformer has enough capacity to safely power the 700 watts appliance.
The amperage that a chandelier draws is based on the amount of bulbs and the wattage of the bulbs used in the fixture. Count the amount of bulbs and multiply that number by the wattage of the bulbs. Take this total wattage and use this formula. I = W/E. Amps = Watts/ Volts.
The measure of the electric power an appliance uses is called wattage. It is typically expressed in watts on the appliance's label or specifications. The wattage helps determine the energy consumption and cost of operating the appliance.
Amps (current) times volts = watts. so watts divided by volts = current (Amps). i.e.- 0.5 Amps.
The total amps on the circuit exceeds 15 amps. It is possible your appliance is drawing more than 15 amps, but more likely that there are other things on the circuit causing the total current to be exceeded.
Voltage X amps = wats 120 volt freezer drawing 2 amps is 240 watts running note it can take up to 3 to 4 times that to start. you have rla run load amps then you have LRA Lock rotor amps (what it takes to start)
The heater should have a wattage rating (very few list amps). Calculate the amps using the wattage and voltage. Amps = Watts/Volts(480).
It is a measure of electrical power. It is Voltage multiplied by Amps. All electrical applicances should give it's wattage or at least it's voltage and Amps so you can work out the wattage. It should be noted that that figure is the maximum that appliance would use.
There are many models under the Mixie label. Look for the name plate and it will give you all of the information. If the wattage is not on the nameplate use the following equation to find wattage. W = A x V. Watts = Amps x Volts.
Yes, you can use a 1000 watts transformer with a 700 watts appliance. The transformer's capacity should be equal to or greater than the appliance's wattage to prevent overloading or damage. In this case, the 1000 watts transformer has enough capacity to safely power the 700 watts appliance.
Power = volts times amps, so an appliance drawing 10 amps at a line voltage of 110 volts is consuming 1,100 watts. Keep in mind, however, that in a non purely resistive load, the phase angle of amps to volts might not be zero degrees, so the calculation becomes more complex, and depends on power factor, or phase angle.
Watts = Volts x Amps x Power Factor To make your calculation you need to plug-in the Voltage and Power factor. The Power Factor is a value from zero to one with one being a pure resistive load.
Basically if you know the Voltage supply and the power used by an appliance then you use the formula for power which is Power = Volts x Amps. Rearrange so Amps (current) = Power / Volts If power was 2400 Watts and Volts was 240 the Current would be 2400 / 240 = 10 Amps
There are zero watts in 300 amps. Watts are the product of amps times volts.