0
red = positive black or blue is negative and green and yellow = earth
In the USA, black is considered L1 (or load 1). Red is considered L2 (or load 2). White is considered neutral, and green is considered ground or earth.
White can sometimes carry the L1 or load, as in a return from a switch. Normally an electrician places an identifier on the white wire to note that it is carrying load.
Wiki User
∙ 12y ago
In the United States, the color code for electrical cords typically follows this standard: black or red is for hot wires, white is for neutral wires, and green or bare copper is for ground wires. It's important to note that colors may vary in different regions or countries due to local regulations.
Wiki User
∙ 12y agoIn a cord or flex for a small electrical appliance there is always a "Hot" or "Live wire, a "Neutral" wire and maybe also a "Ground" or "Earth" wire.
The "Hot" or "Live" wire is colored:
* Black in the US, Canada and other countries using a similar 60 Hz household AC power system.
* Brown in Europe and other countries using a similar 50 Hz household AC
power system.
The "Neutral wire is colored:
* White in the US, Canada and other countries using a similar 60 Hz household AC power system.
* Blue in Europe and other countries using a similar 50 Hz household AC power
system.
The "Grounding" or "Earth" wire is colored:
* Green in a cord or flex in the US, Canada and other countries using a similar 60 Hz household AC power system.
* Green and Yellow in Europe and other countries using a similar 50 Hz household AC power system.
For more information see the answers to the Related Questions shown below.
Answer for USA, Canada and countries running a 60 Hz supply service.
If you are constructing an extension cord make sure that the ends go on the right end of the cable. Match the wire end when looking at it, to the proper pin configuration of the plug. Looking at the plug from the blade side directly on you should see a larger blade (silver) on the right, smaller (brass) blade on the left and a U shaped ground blade on the bottom. The white wire connects under the right (silver) coloured screw, the black wire connects under the left (brass) coloured screw and the green wire under the green ground screw. Looking at the end of the cable it should be matched to this configuration. If it doesn't, look at the other end of the cable. No wires should cross when connecting to the blades on the plug, if they do you have the wrong end of the cable.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Add your answer:
Earn +20 pts
What is the smallest wire size you can color with tape?
It is generally not recommended to color wires with tape as it can lead to safety hazards and code violations. It is best to use colored electrical tape for labeling and marking purposes, not for changing the color of wires.
110v electrical wire color code for construction site?
In the US, typically, black and red wires indicate hot conductors, white wires indicate neutral, and green or bare wires indicate ground. It's important to always consult local electrical codes and regulations as wire color codes can vary by location. Make sure to use the correct wire gauge for the electrical load to ensure safety and proper functioning.
What is the color code for live wire?
The color code for a live wire can vary depending on the country, but in general, it is typically red, brown, black, or any color other than green, white, or gray. It's important to always consult local electrical codes and regulations to determine the correct color coding for wires.
Where is the wire code for the lights?
The wire code for lights can typically be found in the electrical wiring diagram that corresponds to the specific lighting system. The wire code is a reference to the color-coding used for the electrical wires in the system, indicating which wire performs which function. If you are unable to locate the wire code, consulting an electrician or the manufacturer's documentation for the lighting system may provide the necessary information.
How can one tellwhich wires in the wall are from the power source and which are from the heater when both the wires are the same color?
To determine which wires are from the power source and which are from the heater, you can use a multimeter to test for voltage. Turn off the power to the circuit, then use the multimeter to check for voltage on each wire. The wire with voltage when the circuit is off is from the power source, while the wire with voltage when the heater is on is from the heater. Be sure to proceed with caution and follow all safety guidelines when working with electrical wires.
What is the electrical code for dropping so cord from bar joist?
Under electrical code 368.56(B), flexible cords and cables can be attached to building surfaces. However, under electrical code 400.8, flexible cords and cables are not permitted to be dropped from a bar joist.
What is the colour code for neutral in electrical wires in Ghana?
Black
110v electrical wire color code for construction site?
In the US, typically, black and red wires indicate hot conductors, white wires indicate neutral, and green or bare wires indicate ground. It's important to always consult local electrical codes and regulations as wire color codes can vary by location. Make sure to use the correct wire gauge for the electrical load to ensure safety and proper functioning.
What is the color code for live wire?
The color code for a live wire can vary depending on the country, but in general, it is typically red, brown, black, or any color other than green, white, or gray. It's important to always consult local electrical codes and regulations to determine the correct color coding for wires.
Where is the wire code for the lights?
The wire code for lights can typically be found in the electrical wiring diagram that corresponds to the specific lighting system. The wire code is a reference to the color-coding used for the electrical wires in the system, indicating which wire performs which function. If you are unable to locate the wire code, consulting an electrician or the manufacturer's documentation for the lighting system may provide the necessary information.
Can two separate wires in parallel be used to increase the amperage capacity?
Yes they can but the electrical code states that the wires can only be 1/0 AWG and larger.
Wire color code?
There are many reasons why wires have color codes. This is to ensure the right wire goes to the right place.
Need to know the color code for tail light wires for a Honda spirit motorcycle?
6
What did samuel morse's telegraph use to transmit messages?
The first electrical telegraphs used Morse Code, sent as long and short electrical impulses along wires.
What color wire code for ignition and starter wire?
Unfortunately, there isn't a single universal color code for wires in the car. Usually, the red wires power the vehicle, and the brown wires handle the starter.?æBefore anything else, however, make sure you have proof that you own the car. Hotwiring can get you in a buttload of trouble if you don't.
What are the wiring color codes for automotive vehicles?
Wiring color codes are the identification colors that color the wires in your automobile. For example, if you have a British car the blue, blue and white , and blue and red wires are for the headlights. The red and white wires are for the instrument lights, and the green and white and green and red wires are for the turn lights. The color code simply identifies what that wire does. Could you imagine if all of the wires were the same color. You couldn't identify anything in a harness.
How can one tellwhich wires in the wall are from the power source and which are from the heater when both the wires are the same color?
To determine which wires are from the power source and which are from the heater, you can use a multimeter to test for voltage. Turn off the power to the circuit, then use the multimeter to check for voltage on each wire. The wire with voltage when the circuit is off is from the power source, while the wire with voltage when the heater is on is from the heater. Be sure to proceed with caution and follow all safety guidelines when working with electrical wires.
