Romex, All you have to do is go to a hardware store and tell them you need house wire. It comes in a box. I am not sure how many feet. If you are just looking for the gauge, they will know that too.
No, it is not recommended to use a 14-gauge Romex cable for receptacles. A 14-gauge wire is typically used for lighting circuits, while a 12-gauge wire is usually used for receptacles to handle the higher current requirements. It is important to match the wire size with the intended usage for safety and code compliance.
Mixing different gauge wires in the same circuit is not recommended as it can lead to electrical hazards. It is better to use the same gauge wire throughout the circuit to maintain consistency in the electrical load. If you're adding new lights and outlets, it's best to use the same gauge wire as the existing one.
No, 15 amp rated outlets should be used with 14 gauge wire. For 12 gauge wire, you should use outlets rated for a higher amperage, such as 20 amps, to match the capacity of the wire and reduce the risk of overheating. It's important to match the wire gauge with the appropriate outlet rating to ensure safety and proper functionality.
With a 15 A breaker you need 14 Gauge wire. Normally you would only put 8 outlets on a 15 A circuit. If you have the option you shoudl consider a 20 A circuit, use 20A receptacles and 12 gauge wire. Comment: The question was on a homeowners electrical exam. My answer was also 14 gauge however, the tester said the answer was 12 ga. I thought maybe there was something special about the 10 outlets. For example, 10x180 VA per outlet/120V = 15 A which is right at the limit for 14 ga but would be 75% for the 12 ga wire.
Romex, All you have to do is go to a hardware store and tell them you need house wire. It comes in a box. I am not sure how many feet. If you are just looking for the gauge, they will know that too.
No, it is not recommended to use a 14-gauge Romex cable for receptacles. A 14-gauge wire is typically used for lighting circuits, while a 12-gauge wire is usually used for receptacles to handle the higher current requirements. It is important to match the wire size with the intended usage for safety and code compliance.
Mixing different gauge wires in the same circuit is not recommended as it can lead to electrical hazards. It is better to use the same gauge wire throughout the circuit to maintain consistency in the electrical load. If you're adding new lights and outlets, it's best to use the same gauge wire as the existing one.
Assuming 120 VAC in a residence maximum watts = 15 x 120 = 1800 Watts. For a continuous load you can support 1440 watts which is 80& of maximum. You need 14 AWG gauge wire.
No, 15 amp rated outlets should be used with 14 gauge wire. For 12 gauge wire, you should use outlets rated for a higher amperage, such as 20 amps, to match the capacity of the wire and reduce the risk of overheating. It's important to match the wire gauge with the appropriate outlet rating to ensure safety and proper functionality.
With a 15 A breaker you need 14 Gauge wire. Normally you would only put 8 outlets on a 15 A circuit. If you have the option you shoudl consider a 20 A circuit, use 20A receptacles and 12 gauge wire. Comment: The question was on a homeowners electrical exam. My answer was also 14 gauge however, the tester said the answer was 12 ga. I thought maybe there was something special about the 10 outlets. For example, 10x180 VA per outlet/120V = 15 A which is right at the limit for 14 ga but would be 75% for the 12 ga wire.
No, Romex cable is not allowed to be run inside conduit. Romex cable is intended to be used in exposed or concealed applications within buildings. If conduit is used, it should contain individual THHN/THWN wires instead of Romex cable.
For a 5000 watt dryer, you should use 10-gauge (AWG) copper wire with a 30-amp circuit breaker. This corresponds to a 3-wire, 240-volt circuit with a ground wire. Make sure to consult your local electrical codes and a licensed electrician for accurate installation.
yes
Not legal
Yes unless there were some overarching electric code reason why conduit was used in lieu of Romex. if in doubt ask an electrician.
It's generally recommended to consult with a licensed electrician when making changes to old house wiring. Adding 14-2 Romex wire to old wiring could potentially overload the existing circuits or cause compatibility issues. A professional can assess the situation and ensure that the modifications are done safely and up to code.