0
In the UK, the colours were once black = neutral, red = live, and green = earth. The modern standard colours are now blue = neutral (note the l in blue for left contact in the three pin plug used in the UK), brown = live (note the r in brown for right contact), and green and yellow stripes = earth
In the US, black= hot wire, white= neutral, green or bare= ground (or earth) red= a second hot wire
Add your answer:
Earn +20 pts
What does a two phase outlet look like?
A two-phase outlet has two hot wires and one neutral wire. It typically has four prongs, with two vertical prongs for the hot wires and one horizontal prong for the neutral wire. This type of outlet is commonly used for high-power appliances like stoves and dryers.
What are all of the names of the appliance wires?
The names of common appliance wires include live, neutral, and ground wires. Live wires carry electrical current, neutral wires complete the circuit by returning current to the source, and ground wires provide a path for electricity to safely discharge in case of a fault.
When phase and neutral will short means what will be the voltage in neutral?
If the phase and neutral wires are shorted together, the voltage in the neutral wire will be the same as the phase voltage. This is because the short circuit effectively bypasses any impedance or resistance in the circuit, causing the potential difference between the phase and neutral wires to be equal.
I have Two black wires and one red wire conected to a switch. Which is hot and which is neutral?
The red wire is typically the hot wire and the black wires are neutral wires. However, it's important to verify the connections using a voltage tester to ensure correct wiring and avoid any electrical hazards.
What does a neutral atom in its ground state look like?
This atom hasn't an electrical charge.
Where on a Mazda auto 1994 is the park and neutral switch?
if you look on the transmission, you should see two wires connected to the neutral switch.
What does neutral do?
Neutral wires are actually ground wires. They enable the circuit to be completed.
What does a two phase outlet look like?
A two-phase outlet has two hot wires and one neutral wire. It typically has four prongs, with two vertical prongs for the hot wires and one horizontal prong for the neutral wire. This type of outlet is commonly used for high-power appliances like stoves and dryers.
What's the different between white and green wires?
white wires are neutral. green wires are ground wires.
What does the neutral safety switch look like and were is it located on a 1993 Buick lesabra?
what dose the neutral safety switch look like and were is it located on a 1993 buick lesabra at
Do you bypass the neutral safety switch by connecting the 2 wires at the ignition switch or the neutral switch?
Neutral switch
What are all of the names of the appliance wires?
The names of common appliance wires include live, neutral, and ground wires. Live wires carry electrical current, neutral wires complete the circuit by returning current to the source, and ground wires provide a path for electricity to safely discharge in case of a fault.
Why are the 3 wires colors?
Earth, Neutral and Acttive.
How do you bypass neutral safety switch on Toyota t 100?
Look at the connector to the neutral switch, on the passenger side, at the tranny, there should be two No. 12 wires. These are the wires that tell the computer the truck is in neutral or park. The other smaller wires are for the shift position lights and the reverse lights. You can either cut these wires and connect them together of get a 4" piece of wire and two spade connectors to make a loop and connect them to the pigtail connector. Alternatively you can remove the switch and trun it to the park position and attach it to the body. Hope that this helps.
How do you bypass neutral safety switch on 1997 Toyota t-100?
Look at the connector to the neutral switch, on the passenger side, at the tranny, there should be two No. 12 wires. These are the wires that tell the computer the truck is in neutral or park. The other smaller wires are for the shift position lights and the reverse lights. You can either cut these wires and connect them together of get a 4" piece of wire and two spade connectors to make a loop and connect them to the pigtail connector. Alternatively you can remove the switch and trun it to the park position and attach it to the body. Hope that this helps.
Do you attach the red wire to the brown and black to the blue for a light?
No, typically red wires are connected to hot/live wires and black wires are connected to neutral wires. Blue wires are often used for connecting to neutral wires as well. Remember to always follow the wiring instructions provided with your specific light fixture.
Why neutral is earthed always?
The two wires carrying a standard ac power supply are the live and the neutral. By convention one of the two wires is earthed at the transformer providing the supply. That then becomes the neutral and the other wire is the live.
