0
The wattage needed for a clone depends on its size and stage of growth. Typically, clones require lower wattage of around 20-40 watts per square foot during the initial rooting phase, and this can be gradually increased as they grow and enter the vegetative stage. It is important to monitor the plants for any signs of stress and adjust the wattage accordingly.
Add your answer:
Earn +20 pts
What wattage Grow Light should I use?
Optimal wattage depends on several factors including the size of the growing area and the type of plants. Plants that require more light (i.e. tomatoes), need a higher wattage system.
Can you use 110v chandler in 220v country by changing a 220v light bulb The chandler said max 100w light bulb so do you need to use a smaller watts of a 220v light bulb?
No, changing the light bulb wattage would not convert the chandelier from 110v to 220v. You would need a voltage converter or transformer to safely use a 110v chandelier in a 220v country. As long as the replacement bulb stays within the maximum wattage specified by the chandelier, you can use the original wattage.
What is the calculated wattage of a computer that draws 4 A of current?
To calculate the wattage of a device, you need to know both the current (in amperes) and the voltage (in volts). If the voltage is not provided, you cannot accurately calculate the wattage. In this case, with only the current (4 A) given, you cannot determine the wattage without knowing the voltage as well.
How can wattage convert in kilovolts?
To convert wattage to kilovolts, you typically need more information. Wattage is a measure of power, while kilovolts are a measure of voltage. The conversion will involve using the formula P (watts) = V (volts) x I (current), where V is the voltage in kilovolts. By rearranging the formula to solve for V, you can convert wattage to kilovolts if you know the current as well.
110 volt motor 14amp pull how big of a 12 volt converter do you need to run this?
converters are usually listed in Watts output- sometimes with a surge wattage about 2 times the normal running wattage- motors usually have a surge need to start and then even out- so assuming this motor runs at 14amp= Watts = volts X amps, you should need 1540 watt converter- 2000 watt converter to be safe
Should you clone people or things?
you should because if you need a transplant, your clone could donate blood or an organ to you.
What wattage Grow Light should I use?
Optimal wattage depends on several factors including the size of the growing area and the type of plants. Plants that require more light (i.e. tomatoes), need a higher wattage system.
How much wattage does your 12 inch alpine type e sub need?
At least 1000
What is the best wattage for a hair blow dryer?
A 1200 watt blow dryer is the highest legal wattage that you should go. At this wattage you will still be able to plug into a 120 volt 15 amp receptacle without blowing the breaker. Any blow dryers with wattage's below 1200 watts should be purchased depending on what the temperature of the air you need to dry your hair. Keep in mind the lower the wattage the lower the air temperature and the longer it will take for your hair to dry.
How many amps do you need if you have a 480 volt space heater?
The heater should have a wattage rating (very few list amps). Calculate the amps using the wattage and voltage. Amps = Watts/Volts(480).
How much amperage does a three foot base booard heater draw?
You need to mention the voltage and wattage of the device to get the right answer
Should you play your bass amp at full volume?
NO. If you need more volume, go for a larger amp with more output wattage.
What do you need to clone a mouse?
A degree.
Do you need a data plan for the fake iPhone 4?
probaly i mean a clone is a clone rite
How much power is 1000000 volts?
1,000,000V is not a measure of power. You need the amperage in the equation to figure out the power (wattage). W = A x V
How can you clone Pokemon in xd?
You need to get a GLITCH
What are the wattage requirements for outdoor string lights?
The wattage will depend upon the type of bulb and the number of lights on the string. It will tell you on the package what each bulb requires in wattage, so you only need to multiply that by the number of bulbs in the string. so, number of bulbs x wattage requirement for each bulb = wattage requirement.
