0
How long should it take for a marble to hit the bottom of a glass cylinder filled with oil?
Wiki User
∙ 13y ago
The time it takes for a marble to hit the bottom of a glass cylinder filled with oil will depend on various factors such as the size and weight of the marble, the viscosity of the oil, and the height of the cylinder. Generally, it should take a few seconds to a minute for a marble to reach the bottom.
Add your answer:
Earn +20 pts
Can plumbers putty be used on a faucet installation in a marble sink or counter-top?
No, plumber's putty should not be used on marble surfaces as it can potentially stain or damage the marble. It is recommended to use silicone caulk specifically designed for marble or other sensitive surfaces when installing faucets in marble sinks or counter-tops.
Do you measure volume to the top or bottom of the muniscus?
When measuring the volume of a liquid in a graduated cylinder or similar container, the volume is typically measured to the bottom of the meniscus (the curved surface of the liquid). This is because the liquid forms a concave shape at the edges due to surface tension, and the volume should be read at the lowest point of the curve for accuracy.
Why should oxalic acid not be used on marble tiles and counters?
Oxalic acid can react with the calcium carbonate in marble, causing etching and dulling of the surface. It can also potentially weaken and damage the marble over time. It is best to avoid using oxalic acid on marble to prevent these negative effects.
When reading the volume of fluid in a graduated cylinder the eye should be?
When reading the volume of fluid in a graduated cylinder, the eye should be at the same level as the meniscus (the curve at the surface of the liquid). This helps to avoid parallax error and ensures an accurate reading of the volume.
How do you read meniscus on a graduated cylinder?
All liquids have a surface tension. This tension creates a meniscus or curve on the surface, most noticeable in small diameter tubes or cylinders. The meniscus of water curves up the sides of the cylinder, while heavy liquids like mercury curves down the cylinder. You should always measure light liquids at the bottom of the meniscus and heavy liquids at the top of the meniscus.
What figure is at the bottom view of a cylinder?
If its a regular cylinder, it should be a circle.
Where is the coolant drain in 1999 6-cylinder?
Should be at the bottom of the radiator.
Where is the starter on a grand am and best way to access it?
4 cylinder should be at the front of engine behind radiator 6 cylinder should be at the rear passenger side at the bottom of engine
When reading the volume of fluid in a graduated cylinder the eye should be .?
Level with the bottom of the fluid's meniscus
Can you put a yz250 head and cylinder on a yz125 bottom end?
If there the same year it should fit.
When you are measuring the volume of water in a graduated cylinder do you look at the top of the meniscus or the bottom of the meniscus?
You should always measure the volume of liquid in a graduated cylinder at the bottom of the meniscus, where the curve of the liquid meets the cylinder's surface. This ensures an accurate reading of the volume contained in the cylinder.
When reading a graduated cylinder you look at?
When you read a scale on the side of a container with a meniscus, such as a graduated cylinder or volumetric flask, it's important that the measurement accounts for the ... For mercury, take the measurement from the top of the meniscus. ...
If a large leak of refrigerant occurs such as from a filled cylinder in an enclosed area what action should be taken when no self contained breathing apparatus is available?
Run
How do you remove key cylinder on a 1997 Lincoln mark viii?
There are two (2) torque screws that hold the cylinder itself onto the car. Remove both and the cylinder should fall out. (this is the hard way) Remove one (1) Torque screw, bottom. Then turn the key to the ON position (not running) and then press the tab that holds the cylinder in and the cylinder itself should fall out. (this is the easy way)
When using the measuring cylinder do you talk the measurement at the side of the cured surface or the curved surface?
I think you are talking about a graduated cylinder. When measuring liquids in a grad. cylinder you should read at the bottom of the miniscus ( the curved surface of the water or other liquid).
Why should you tilt a graduated cylinder when you drop objects in them?
Tilting a graduated cylinder when putting something it in is is so that the object will not break. If you just drop the object straight in it will go straight to the bottom and break.
Where is the alternator located on a 1998 VW Passat 4 cylinder?
v4, it should be on top according to the manual. mine is a v6 and its on the bottom.
