0
The break is usually one of the lights themselves. Take another set of lights that work and one at a time test every light in the string that doesnt work until you find the one that is broken. Its a pain in the backside but there is no shortcut for this.
First, check if any bulbs are burnt out or missing. Replace any faulty bulbs. Next, check for any tight twists or knots in the string that could be causing a short circuit. Lastly, use a light tester to check each bulb socket along the string to identify the faulty one.
your BEST chance: http://lightkeeperpro.com/default.asp For those that don't enjoy the tedious process of discovering which bulb or bulbs need to be replaced, you can contact www.ChristmasTreeRepair.com to solve this problem for you. ChristmasTreeRepair.com currently operates in the Des Moines, IA, metro area. They will come out to your house or business and fix the problem onsite for you. Arrangements can also be made to have the item shipped and repaired if located outside of the Des Moines, IA metro area.
the best way to string lights on a Christmas tree is to have two people on opposite sides of the tree and start wrapping the tree with the lights from the top to the bottom. Lay the lights on the branch ends. Depending on how many lights you have you will have to guess how many times you wrap the lights around.
If you've noticed how pre-lit trees are wired, they begin from the base of the trunk, and move outward to branches, then back in again to the next branch, and from there "out and in" again on the next branch over, repeating the process from the bottom of the tree to the top.
The general rule of thumb is that you should have 100 lights for every foot of tree height, so if you have a 7' tall tree you should use 700 lights. Using the process above produces a very fully-lit tree that glows from the inside as well as out.
The color of the lights you use is, of course, a purely aesthetic choice. One thing: you should always be conscious of how many light strings you can attach in a row (to each other). The box the lights came in should tell you how many can be attached in sequence. If you have a pre-lit tree and are "re-stringing" it, you can probably use the multiple outlets that are already provided in the trunk of the tree. If you're stringing a real tree, you may want to run a multi-socket extension cord half-way up the tree, and plug several groups of lights into the (usually) three outlets at the head of the extension cord.
If you want to get inventive, as I did, you could try something like this. When several strings of lights failed on my pre-lit tree, I removed them all and bought new strings. But my new strings are not all the same. I bought several long strings of red, white and green standard midget lights. I wrapped them around the tree, but more loosely than my original lights. In other words, I left space on the tree to add other lights.
Then I bought several strings of "globe" lights. These are the ones that look like pearl-type beads. I got these in red, white and green also. I strung these lights in-between the ones I'd already put on.
But I wasn't done yet. I still left a little space for a few more strings of lights that look like clusters of holly berries, with little fake holly leaves around them. I filled in the remaining spaces with these.
If you do it right, the result is a beautiful multi-faceted look with different types of lights that really complement each other all around the tree. Much more interesting than your typical pre-lit tree!
The only bad thing is, if you want these "specialty" types of lights, you really have to get them around, say, Halloween. I'm not kidding. They sell out fast and stores don't re-stock until the following year. The first Christmas I wanted to try this, I went shopping for lights the second week of November, and they were already almost all gone.
Add your answer:
Earn +20 pts
Where is the load on a string of Christmas lights?
The load on a string of Christmas lights is typically located in the bulb itself. Each bulb is designed to produce light and consumes power when electricity passes through it. The collective load of all the bulbs on the string determines the amount of power required to illuminate the lights.
Will a 240 volt string of Christmas lights work on a 110 volt socket?
No, a 240 volt string of Christmas lights is designed to be used with a 240 volt socket. Plugging it into a 110 volt socket may damage the lights and pose a safety hazard. Be sure to always use lights with the correct voltage rating.
Christmas lights Why do half of the string doesn't work?
One common reason why half of a string of Christmas lights may not work is a broken or loose bulb causing a break in the circuit. Another possible cause could be a damaged wire or a blown fuse in the string of lights. Sometimes issues can also arise from a faulty socket or plug connection.
How much electricity does Christmas lights use per hour?
The average strand of Christmas lights pulls about 1 amp, which is roughly the same as a 100 watt light bulb running on 120 volts. It's hard to say how much running it will cost you for electricity, but one thing is sure: no one wants to leave their light on all day, same goes with the Christmas lights.
How are Christmas lights different now than before electricity?
They have been invented, manufactured and installed.
Where do you purchase fuses for Christmas string lights?
At a hardware store.
How do you hang Christmas lights on a roof?
You use some string
How do you know which light bulb is bad on a Christmas string of lights?
Plug the "string of lights" into the power point. If a particular light does not come on, then it is "bad".
Where is the fuse typically located on a string of christmas lights?
The fuse is located where the AC outlet is. There are actually two fuses.
What are the most popular types of Christmas window lights?
The most popular types of Christmas window lights right now are LED, Solar, or String lights. Icicle christmas lights tend to be quite popular these days as well.
How do you run Christmas lights on batteries?
You will have to buy battery powered Christmas lights.
The first string of Christmas lights were hung up by wealthy easterners in what year?
1902
Where is the load on a string of Christmas lights?
The load on a string of Christmas lights is typically located in the bulb itself. Each bulb is designed to produce light and consumes power when electricity passes through it. The collective load of all the bulbs on the string determines the amount of power required to illuminate the lights.
What kind of lights do you use to decorate a Christmas tree?
Mini string lights, LED lights, and novelty lights like icicle or globe lights are commonly used to decorate a Christmas tree. These lights come in various colors, sizes, and patterns to create a festive atmosphere. Make sure to check the safety and compatibility of the lights with your tree before decorating.
What can you use a parallel circuit for?
Christmas tree lights, this parallel circuit prevents one bulb failure from turning off the whole string of lights.
What is the difference between series and parallel Christmas lights?
With series Christmas lights, if one burns out, the whole string stops working. With parallel Christmas lights one light burning out only affects that light. This makes it much easier to replace burned out lights in the case of the parallel lights.
A string of Christmas tree lights has 15 lights One of the lights does not work What is the probability that the defective light is the third one from the plug?
1/15
