0
You can check out the related link below.
Wiki User
∙ 13y ago
To convert Shore scale C to Rockwell scale C, there is no direct formula as they measure hardness differently. Shore scale C measures indentation hardness while Rockwell scale C measures depth of penetration. These two scales cannot be directly converted into one another.
Add your answer:
Earn +20 pts
Shore hardness 60 deg c relates to what shore hardness in d scale?
Shore hardness 60 deg C corresponds to approximately Shore D 75 on the Shore hardness scale.
What is the hardness of 4140 Plate?
The hardness of 4140 plate typically ranges from 28 to 32 HRC (Rockwell C scale) when heat treated to achieve desired mechanical properties.
Convert 125 degree Celsius to Kelvin scale?
The answer is 398.15 K (approx.). The Kelvin scale starts at absolute zero and is used in scientific laboratories. Celsius is for general use and set 0 and 100 as melting and boiling point of water respectively. To convert from C to K, add 273.15 to C.
What is -175 C on the Kelvin scale?
The answer is 98.15 K (approx.). The Kelvin scale starts at absolute zero and is used in scientific laboratories. Celsius is for general use and set 0 and 100 as melting and boiling point of water respectively. To convert from C to K, add 273.15 to C.-175 deg C = -175 + 273.15 = 98.15 K
What is the full form of hrc in term of hardness?
The full form of HRC is Rockwell Hardness C Scale. It is a measure of the hardness of a material, typically metals, determined by how much force is required to create an indentation on the surface of the material.
How do you convert Rockwell b scale to c scale?
You dont. Minimum C is about maximum B. And the indentation is different. Even if you could convert it, the results would not be accurate.
What is the Rockwell C for tin?
Approx 37.8 Rockwell "c" scale
How hard is a diamond in Rockwell Scale c?
Diamond is more than 1000 times harder than quartz, which is in the 80 range in the Rockwell C. Diamond cannot be measured on the Rockwell C scale. A diamond pyramid is actually used in the Rockwell C test, which would be inconclusive.
Shore hardness 60 deg c relates to what shore hardness in d scale?
Shore hardness 60 deg C corresponds to approximately Shore D 75 on the Shore hardness scale.
When reading the steel heat treatment notation RC what does the R mean?
RC stands for Rockwell Hardness C scale; the different letters A,B,C etc. are based on different loads and indenters for measurement. C scale is typical for steels, while B scale is typical for aluminum. There are conversion tables for these if needed.
A very hard tool steel will probably register about 70 on the what scale?
Rockwell C scale
How do you convert Shore A 92 to Shore C?
You can't. It's a different test method.
What is HRC in rockwell testing machine?
HRC stands for Hardness Rockwell C scale. There are different scales; C is probably the most common for hardened materials. See the related link for more information.
Is a 35 high on the Rockwell C Scale?
Yes, a reading of 35 on the Rockwell C Scale would be considered relatively low as the scale generally ranges from 20 to 70. This indicates that the material is softer compared to higher readings on the scale.
What is the hardness of copper on rockwell scale c?
It can't be accurately converted.The softest metal on the C scale gets a 1 rating.That 1 rating is the equivalent of 82 on the B scale, which is the Rockwell scale used for copper.Copper and all it's alloys are down around the 40 range of the B scale.And you can't assume that a B scale 40 is half of a C scale 1, either. Since the tests use different metal ball sizes, it's an issue of being an unequal scale.
What is the Hardness Rockwell C scale?
This is a method used to determine the hardness of a metal. If you know the type of metal and the hardness, this will tell you the Tensile Strength of the metal and how well it was heat treated. The method uses a ball or a pin to strick the metal and leave a small indention. The size and depth that the ball makes in the metal is inversely proportional to the hardness. Using the scale, you can then determine if the part has completed the proper heat treatment as required by the Engineering drawing. There are 3 Rockwell scales: A, B, C. Rockwell C scale is for the hardest of metals such as steel. Rockwell B is for metal such as soft aluminum and A is for even softer metals.
Convert -146ô C to the Kelvin scale?
-146 deg C = 127.15 K
