The only place that white neutrals should be connected to the ground wires is upstream of all branch circuit breakers at the ground bus bar inside the main breaker panel.
The answer given below gives DANGEROUS ADVICE because it fails to explain exactly what a separate ground wire does.
Where they are provided in a circuit - such as in 4-wire 240 volt outlets - the green or bare copper ground wires must be kept separate from the neutral (white) wires everywhere except in the main breaker panel at a single point upstream of all circuit breakers.
The whole purpose of providing a ground wire in a circuit is for it to be connected directly to any the internal metal frame and external metal casings of all appliances which it supplies with power.
Then, if an accident occurs which causes physical damage to the appliance (or its connecting cord or plug) - or if some electrical insulation fails or some other kind of breakdown occurs, which could make the appliance catch on fire or electrocute the user - the ground wire is there as a safety wire to "ground" the fault condition.
The result is: before any further damage is caused to users or their home, the heavy fault current the ground wire takes will make the circuit breaker trip to cut off the electricity.
<><><>
In normal households in North America and other countries which use the same 60 Hz supply service -
4 wires are Red (Hot), Black (Hot), White (Neutral) and Bare (Ground)
3 Wires are Red (Hot), Black (Hot), Green (Neutral/Ground) - generally not used for 220-240V - or may be Black (Hot), Red (Hot) and Bare (Ground) or Black (Hot), White (Hot), Bare (Ground).
The following advice is dangerous and should not be followed:
There is NO difference between the White, Green, or Bare wires. They all get connected to the same place in the breaker box - the neutral strips on the sides of the box. Use of the bare ground is for personal safety only - however the white or green wire does the exact same job.
So to answer your question
(Breaker Wire : Appliance Wire)
Red : Red
Black : Black
White : Green
Bare - connects to the frame or case of the outlet/box you're wiring into.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
telescope s
You should not use the equipment until you have been trained.
A graduated cylinder would be the most appropriate piece of equipment to accurately measure 85 mL of water. It has precise markings that allow for accurate measurement of liquid volumes.
It requires two pieces of equipment: a ring stand and a ring.
A ladder is typically considered as a piece of equipment rather than a tool, as it is used for access and support rather than manipulation or work.
Any of them might be connected to a router, but if it connects to a piece of equipment provided by an ISP, usually the ISP's equipment will have the DCE connection, and the router will have the DTE connection. The DCE connection is the "master" part - the part that controls the transmission speed.Any of them might be connected to a router, but if it connects to a piece of equipment provided by an ISP, usually the ISP's equipment will have the DCE connection, and the router will have the DTE connection. The DCE connection is the "master" part - the part that controls the transmission speed.Any of them might be connected to a router, but if it connects to a piece of equipment provided by an ISP, usually the ISP's equipment will have the DCE connection, and the router will have the DTE connection. The DCE connection is the "master" part - the part that controls the transmission speed.Any of them might be connected to a router, but if it connects to a piece of equipment provided by an ISP, usually the ISP's equipment will have the DCE connection, and the router will have the DTE connection. The DCE connection is the "master" part - the part that controls the transmission speed.
Is a piece of circuit - switched network equipment used in telecommunications network.
Point of connection to the electrical system for a particular piece of equipment, normally reserved for the exclusive use of the equipment, sometimes called a dedicated circuit.
A vacuum breaker tail piece 11/2" x 3/4" x 9"
A circuit breaker is designed so that it will trip when the electric current is too high. That is the purpose of a circuit breaker. If there is a metal piece on the circuit breaker that prevents it from tripping, it is useless. Perhaps someone has altered it.
Because it needs to be able to cut the power to the load. That's why circuit breakers are always the first piece of equipment in a circuit after the power supply.
An SPN isolator switch is a circuit breaker; they are a device, which when used can automatically switch off the flow of electricity. They are used to protect a piece of machinery or equipment from damage by an overload of electricity.
A breaker trips because the circuit load has tried to draw more current that the circuit is designed to operate at. You have to establish what the total current draw of the device is. This can be found on the manufactures label. There it will state what the normal amperage draw is for the specific piece of equipment. If the breaker has tripped, look for the cause and rectify the problem before resetting the breaker. If you found the problem and corrected the cause, the breaker will reset and stay in the on position.
An SPN isolator switch is a circuit breaker; they are a device, which when used can automatically switch off the flow of electricity. They are used to protect a piece of machinery or equipment from damage by an overload of electricity.
That is when a piece of equipment has a failure and will not work.
In a BMS system, starting and stopping of a piece of equipment is done by the operator.In a BMS system, starting and stopping of a piece of equipment is done by the operator.
The Randoseru is a backpack like piece of school equipment from Japan.