0
Add your answer:
Earn +20 pts
What is it called when a rock bends instead of breaking due to plate movement?
When a rock bends instead of breaking due to plate movement, it is called ductile deformation. This usually occurs under high pressure and temperature conditions deep within the Earth's crust.
How does a bi-metallic strip change in temperature?
A bi-metallic strip bends when exposed to temperature changes due to the different thermal expansion coefficients of the metals it's made of. One metal expands more than the other, causing the strip to curve toward the metal with the higher coefficient when heated and in the opposite direction when cooled.
What is high static pressure?
High static pressure refers to the resistance encountered by air or fluid flow within a system, such as ducts or pipes. It is commonly found in situations where the flow encounters obstacles like filters, bends, or long distances. High static pressure can have a negative impact on the efficiency and performance of equipment like fans and pumps.
How many 90 degree bends can you have in one run of conduit from box A to box B?
In general, it is recommended to limit the number of bends in conduit to 360 degrees (four 90-degree bends) for proper cable installation. Exceeding this limit can affect cable performance, make pulling cables difficult, and increase the risk of damage to the conductors.
How many degrees of bend is allowed in a conduit between boxes?
It is generally recommended not to exceed 360 degrees of total bends in a conduit run between boxes. Any more bends may make it difficult to pull wires through the conduit and can affect the efficiency of the electrical system.
What is the element which bends with temperature and is used in thermostatic switches?
Bimetallic strip
Does the length of time the bone is in vinegar affect how much the bone bends?
brb
What does bimetallic mean?
A strip consisting of two metals that bends with a rise in temperature
Do bends in a wire affects its electrical resistance?
Unless the wire is broken, a bent wire should still be able to conduct electricity as well as a straight one.
Can anyone explain the use of a bimetallic strip in heat regulation in an electric iron?
When the temperature of the iron increases, the bimetallic strip bends upwards. This breaks the contact between the strip and the heating coil. When the temperature falls, the bimetallic strip bends down and the contact is restored.
What is static pressure in an Oahu?
Static pressure in an HVAC system on Oahu refers to the measurement of the pressure exerted by the air on the walls of the ductwork when the system's fan is not running. It is an important parameter in determining the efficiency and functionality of the system. Static pressure is influenced by factors like duct size, length, bends, fittings, and filter condition.
What are examples of contraction caused by a loss of heat?
Inside a kettle there is a thermostat with two dissimilar metals inside and when one heats up to a certain temperature it flexes to knock off the current. However, when it cools down it bends back or contracts to restart the flow of electricity.
Why bends in a wire do no affect its resistance?
Bends in a wire do not affect its resistance because the cross-sectional area and length of the wire remain the same regardless of the bends. Resistance is determined by these two factors, according to the formula R = ρ*(L/A), where ρ is the resistivity of the material, L is the length of the wire, and A is the cross-sectional area. As long as these parameters remain constant, the resistance of the wire will stay the same.
What do you call it when wood twists or bends?
When wood twists or bends, it is commonly referred to as warping. This can occur due to changes in moisture levels, temperature, or improper drying techniques during wood processing.
What contains a small piece of metal that bends when it gets hot?
A thermostat contains a small piece of metal called a bimetallic strip that bends when it gets hot, allowing it to regulate temperature by opening or closing a circuit.
Which is not influenced by gravity?
Light is not influenced by gravity. It travels in straight lines through a vacuum at a constant speed, regardless of the presence of gravity. Gravity can only affect the path of light when it passes through a medium that bends its path, such as a black hole.
List 3 manufactured bends that can be bought in a wholesalers?
PVC bends, copper bends, and steel bends are commonly manufactured bends that can be purchased at wholesalers. These bends are used in plumbing and HVAC systems for directing the flow of fluids in pipes and tubing.
