0
no, none exist, you have NPT, (National pipe thread) which are tapered and you have BSP which is straight. they have a different thread pitch as well. however you can run into some that are called OSB, (o-ring sealed back), they are usually 9/16-NF, 3/4-NF of 1 1/8-14. NF is National fine.
Yes, pipe fittings can be designed to be compatible with metric pipe systems. These fittings are specifically sized to fit metric pipes, which are measured using the metric system (millimeters and centimeters) rather than the imperial system (inches). Make sure to confirm that the fittings are compatible with the specific metric pipe size you are working with before making a purchase.
Add your answer:
Earn +20 pts
What is pipe take off?
A pipe take off is a method used in plumbing and construction to determine the length of pipe needed for a specific project. It involves measuring the distance between two points where the pipe will be installed and then calculating the necessary length, often taking into account factors such as angles, fittings, and potential bends in the pipe. This helps ensure that the correct amount of pipe is ordered and installed for the job.
Can you use a glue on the fittings of a gas dryer?
No, it is not recommended to use glue on the fittings of a gas dryer. The fittings should be secured using the appropriate fittings and tools specified by the manufacturer to ensure a safe and reliable connection. If you are unsure, it is best to consult a professional.
What are the advantages of copper pipe fittings over plastic?
The advantages of copper pipe fittings over plastic is that copper does not bend or break as easily as plastic, so it lasts longer and is much more reliable as well.
How do you join copper pipe to copper pipe?
To join copper pipe to copper pipe, you can use soldering or brazing. First, clean the surfaces to be joined, apply flux to the areas, heat the pipes evenly with a torch, and then apply solder or brazing material to create a strong bond. Be sure to follow proper safety precautions when working with a torch.
Do Turkey use the metric and the customary system?
Turkey uses the Metric System.The only country that does not use the Metric System is the USA.
Can you use pressure fittings on three-quarter inch OD steel pipe for natural gas fittings for kitchen stove or do you always have to use threaded?
Not sure what you mean by pressure fittings. Threaded fittings for steel pipe are pressure fittings. Steel pipe with a 3/4" O.D. is known as 1/2" I.P.S. (Iron Pipe Size) pipe.
Do you use pipe dope on compression ring fittings?
no
Can you use compression fittings on natural gas pipes?
No. You can use flared fittings with a flaring tool and soft copper pipe.
Are pipings and pipe fittings the same?
No, fittings go over the pipe
How do you rectify leakage on pipe fittings threaded joints without removing the pipe fittings?
You cannot do that effectively without taking the fittings apart,
What does PVF industry stand for?
PIPE-VALVES-FITTINGS (PVF) Basically the industry that sells pipes and fittings to other industries who use them
Is it necessary to use primer with PVC pipe?
Yes, for proper bonding of PVC pipe and fittings. Primer also code requirement.
Where are places in Houston one can buy pipe fittings?
There are a few places in Houston where one can purchase pipe fittings. A good place to try is Pipe Fittings. Another good place to try is Home Depot.
Are pipe and pipe fittings can be different schedule?
No, they need to match.
What has the author Thomas S Walsh written?
Thomas S. Walsh has written: 'Plastic pipe and fittings' -- subject(s): Plastic Pipe, Pipe fittings, Standards
What does wpb stand for in pipe fittings?
Worught Pipe Bend
How much liter of glue require for one meter of pipe?
The amount of glue that you use on pipe depends on the number of joints or fittings - not length of pipe. - One litre is a lot of pipe glue ! -I have done thousands of feet of PVC pipe and fittings this past year, and still have some glue left in my litre can of Weld-On 711.
