0
Yes a T12 lamp socket will take a T8 tube. The T8 tube will not operate. The T8 ballast is an electronic ballast where as the T12 ballast is a magnetic type. If you are changing over fluorescent fixtures to the smaller T8 lamps then the ballast has to be changed and the end sockets have to be rewired. The schematic on how to do the rewire is on the electronic ballast's label.
No, you cannot replace a T8 bulb with a T12 bulb in the same fixture. They have different diameters and require different ballasts to operate. It is best to use the correct type of bulb for your fixture to ensure proper functionality and safety.
You shouldn't because the ballast in the light most likely is older and won't b compatible with T5's. The bulb could flicker , basically not function correctly
Add your answer:
Earn +20 pts
What is a keyless light fixture?
A keyless light fixture is a type of light fixture that does not have a switch or socket that can accommodate a light bulb. Instead, it is typically wired directly to a power source and requires a light bulb with a built-in switch for operation.
How do you change a fluorescent bulb?
First, make sure the power is turned off to avoid electrical shock. Next, locate the end of the bulb and gently twist to remove it from the fixture. Replace with a new bulb of the same size and wattage by inserting it into the fixture and twisting until securely in place.
If a fluorescent light blinks is the light bulb bad or the ballast?
If a fluorescent light blinks, it is more likely that the issue is with the ballast rather than the light bulb. The ballast helps regulate the flow of electricity to the light bulb, so a flickering light is often a sign that the ballast is failing.
I am installing a kitchen light fixture in the ceiling. While pulling down the old fixture the green ground wire broke. The new Fixture has a green ground wire. Where do I ground it to now?
You can ground the green ground wire from the new fixture to the metal junction box using a grounding screw or grounding clip. Make sure the junction box is grounded properly to ensure safety.
Can you use New 100 watt bulbs that use 72 watts of power in a 75 watt fixture?
NEVER! NEVER! NEVER! The current draw from a 100W light greatly exceeds the design limits built into the 60W fixture. The end result would be a fire. You can use florescent light bulbs to get more light with less amperage. You get 100 watts equivalent lighting for 23 watts and will not create a fire hazard.
How do you replace turn signal bulbs on a 1987 Chevy Celebrity?
It depends on which bulb is burnt out. If it is the front bulb in the bumper you can reach up behind the bumper and unplug the socket and replace the bulb. You may need to loosen the valance to reach up to the bulb. If it is the bulb in the front side marker just take out the screws and remove the fixture, the socket can then be removed to change that bulb. If it is a rear bulb in a sedan or coupe: 1. Inside the trunk near the quarter panel on the side the bulb is burned out on there are three nuts. Remove the middle nut, it should be in the middle of the tail light fixture. 2 Pull the stud out of the body then pull gently away from the center to remove a tab from the backup light fixture. The fixture should now be loose. 3. Remove the appropriate socket and replace the bulb. Reverse the procedure to reinstall the tail light fixture. If it is a station wagon the lens is held on with screws. Take the screws out and remove the lens. Then replace the proper bulb and put the lens back in place. I
How do you remove the tail light lens from a 1989 Chevy Celebrity?
The tail light lens on a 1989 Chevy Celebrity is part of the tail light fixture and cannot be conveniently removed. If you want to change a light bulb you have to remove the tail light fixture from the car. To remove the tail light fixture: 1. In the trunk next to the quarter panel are three nuts, remove the center nut. It should be in the center of the tail light fixture. 2. Pull the tail light fixture so that the stud comes out of the body, then pull outward to pull the tab out of the backup light fixture. 3. You can now take the appropriate socket out and replace the bulb. Reverse the steps to replace the light fixture.
How do you get the light bulb into the long tube light fixture over bath sink electrician put up lamp and then I said I would put in bulb after painting and now i tube is too long?
Get the right lamp or get the right fixture. Do not attempt to modify the fixture to fit the lamp.
How do a change a tail light in a 1999 Olds Alero?
In trunk remove thumb screw, bend back paneling, remove 3 thumb screws and pull out whole tail light fixture. Now you can replace bulb(s).
How do you change the high mount brake light bulb on 2004 Honda Pilot?
Hi, I just changed the whole fixture for the third light. There are two caps on each side of the fixture. With flat screw driver, take off the caps and take out the screws. The light fixture will come out and twist the socket of the light bulb. Now you can able to change the light bulb. I hope this will help you all.
What is a keyless light fixture?
A keyless light fixture is a type of light fixture that does not have a switch or socket that can accommodate a light bulb. Instead, it is typically wired directly to a power source and requires a light bulb with a built-in switch for operation.
How do you change a fluorescent bulb?
First, make sure the power is turned off to avoid electrical shock. Next, locate the end of the bulb and gently twist to remove it from the fixture. Replace with a new bulb of the same size and wattage by inserting it into the fixture and twisting until securely in place.
How do you remove the headlight assembly to replace a bulb?
Modern headlight assemblies are just lenses and are really more part of the body than they were in older cars, to replace most all headlights on modern vehicles look under the hood behing the outer headlight lens and there is a bulb receptacle that inserts into the fixture, now it varies on how to remove it from one manufacturer to the next but that receptacle will either have a locking ring or will simply turn out of the back of the lens and you can pull out and replace the bulb from there. Be careful not to touch the bulb with your fingers to help it last longer, fingerprints or oil will cause the halogen bulbs to burn out quickly.
How do you remove the rear panel in a 1989 Chevy Celebrity to replace a tail light?
To remove the tail light fixture on a 1987 to 1990 Chevy Celebrity sedan: 1. Inside the trunk next to the quarter panel are 3 nuts. Remove the center nut, it should line up with the center of the tail light fixture. 2. Pull back on the tail light fixture until the stud clears the body. 3. Pull outward on the tail light fixture to remove a tab from the back up light panel. 4. Twist the appropriate socket counter clockwise and remove it. You can now replace the light bulb. Reverse the process to put the tail light fixture back in place.
How do you replace the headlight bulb located on a 1998 Toyota Camry?
Hi: My best bet is to remove the plastic container sitting behind the head light. Now, if you want to replace the bulb or complete set, then you have plenty of room to unscrew and replace the whole kit or just replace the bulb. Hope, this helps. I actually removed my battery on my Camry. A pain, but you get LOTS of space to wiggle.
If a fluorescent light blinks is the light bulb bad or the ballast?
If a fluorescent light blinks, it is more likely that the issue is with the ballast rather than the light bulb. The ballast helps regulate the flow of electricity to the light bulb, so a flickering light is often a sign that the ballast is failing.
How do you replace the front turn signal bulb located on a 1994 Mazda 626?
Most of the cars now have composite lights and the lights have to be revomed to replace the bulbs.
