answersLogoWhite

0


Best Answer

the capacitor has 2 wires or poles, one is the ground or negative and the other one is the hot or positive... if it is for car audio amp the ground is connected to the chassis and the positive is connected to the battery and to the positive wire of the amp.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Wiring 1 farad capacitor
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Music & Radio

Is 1 farad capacitor enough for 1000 watts pioneer sub woofer?

It depends on the power rating of the amplifier. The rule of thumb is often said to be 1000 RMS watts per farad. RMS watts is basically the average output of your amp/subwoofer. The power ratings most often given by manufacturers are Peak Watts, ie. how much power the amp/sub can take before breaking down. The RMS wattage is often about half of your Peak rating. So, given that you are running your 1000w Peak Pioneer subwoofer on a 1000w Peak amplifier, and given that both of them are 500w RMS, yes, a 1 farad capacitor would give the amplifier enough juice to run the sub.


What will happen if a diode is connected to capacitor?

the diode when forward biased will conduct and during reverse biased condition(generally doring reverse biased condition ckt is open mens no current flows;when register is connected)current flows but during reverse biased condition 1--for sometimes initially current flows due to discharging of capacitor. 2--then ckt will be having no current


Where can i find A Radio wiring diagram 1995 eagle talon?

In the Haynes Repair Manual, book number 68031 for 1995-2001 Mitsubishi Eclipse and Eagle Talon. Look in Chapter 12 page 39, wiring diagrams 1 and 2.


Where can I find the wiring color code for a Delco car radio?

lots of Auto parts stores will print you a wiring diagram including color codes for free


How do you get a wiring diagram for the interior lights when you open doors on a 95 Jeep grand Cherokee?

www.autozone.com Provides 1 electrical (Main) and 2 body wiring diagrams. http://www.autozone.com/servlet/UiBroker?ForwardPage=/az/cds/en_us/0900823d/80/1f/ec/6b/0900823d801fec6b.jsp This will provide all wiring diagrams for Wrangler from 87 - 95 bruce

Related questions

Unit of capacitor is?

The SI unit of capacitance is the farad. 1 farad is 1 coulomb per volt.


What would be the physical size of a 1 farad capacitor?

When used in car audio applications, a 1 farad capacitor is usually about 6" long and about 2.5-3" in diameter.


What size capacitor you need for a 1000 watts amplifier?

It takes 1 farad for every 1000 watts so u need 2 farads.


Can value of any capacitor be in farad?

A Farad (from Michael Faraday) is the basic unit for capacitance, and a 1 Farad capacitor has a voltage of 1 v across it when the stored charge is 1 coulomb. Most capacitors used in electronics have their capacitance measured in microfarads (10-6 F) or even picofarads (10-12 F).


What does the farad rating mean in capacitors?

The rating or 'size' of a capacitor, called its "capacitance", is related the amount of charge the capacitor can store, to the amount of energy it holds when it stores some charge, and to the opposition of the capacitor to the apparent flow of alternating current through it. If a capacitor has a capacitance of 1 farad, then -- One coulomb of charge stripped off of one plate and added to the other plate produces 1 volt of potential difference between the plates. -- The energy stored in the capacitor is 1/2 the square of the voltage across it. -- Its impedance is (0.159 divided by the frequency) ohms. The farad is an enormous capacitance. A typical capacitor used in a 'lumped' circuit ... the kind of construction where you would buy a capacitor and solder it in ... has a capacitance in the range of maybe 10 picofarads (trillionths of a farad) to maybe 100 microfarads (millionths of a farad).


Which capacitor is best for a 1400Watts amp?

It you mean a cap then it's 1 farad for every 1000 watts. So you would want a 1.5 farad cap. Or a 2 farad would work as well.


What is the capacitance of a capacitor?

Capacitors are built to different specifications depending on application. The higher the capacitance the more charge the capacitor can store.The capacity to store electric charge, when a voltage is applied. Measured in Farad = Coulomb/Volt. In other words, if for every volt applied the capacitor stores 1 coulomb of charge, it would have a capacitance of 1 farad. In practice this is a huge unit, and the capacitance is usually expressed in micro-, nano-, or even pico-Farad.


Can a parallel plate capacitor of 1 farad capacitance having plate separation of 1 mm be actually constructed in laboratory?

no


If picofarad capacitor is replaced with microfarad capacitor then what will happend?

The unit of capacitor is farad. 1 farad =10 to the power of 6 microfarad and also = 10 to the power of 12 picofarad Therfore if you are replacing one picofarad capcitor into one microfarad capacitor you are increasing the capcitance to 1000000 times. If it is in an oscillator circuit you are changing the frequency drastically which will be of no use.


What is fifty microfarads?

Fifty millionths of a farad, abbreviated as 50 uF. Farad is the unit of capacitance. 50 microamps DC flowing for 1 second will charge a 50 uF capacitor to 1 volt.


Why 1 farad capacitor generally is not available in the market?

I'm not sure where you are getting your information. Capacitors come in a large range - nano farad to several farad. The higher the farads, the bigger (in general) the capacitor will be. For example, amazon has a 1 F, 20 volt cap for ~76.00. I would consider this to be "generally available in the market". If you want a 1 farad cap for 120 volts, it's going to be substantially bigger than this one (20 volt is ~5 lbs.).


One farad is equal to?

Farad is a unit of capacitance - to measure the capacity of devices called capacitors. Farad means coloumb/voltage, in other words, if the capacitor has a capacity of 1 farad, it will store a charge of 1 coloumb for every volt. This is a huge unit; real capacitors are usually specified in microfarad, nanofarad or picofarad.