answersLogoWhite

0


Best Answer

It gives the possibility to generate several precise baudrates for serial communications. With 12 MHz you introduce small errors that will however be acceptable for hobbyists.

User Avatar

Wiki User

βˆ™ 12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Why 11.0592 MHZ frequency is used with at89c51?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is range of crystal oscillator frequency in ATMEL89C51?

Atmel posts the datasheet for their AT89C51 and other microcontrollers on their website (see link below). That datasheet specifies that the Atmel AT89C51 is operational for an oscillators in the range 24 MHz to 0 Hz (fully static paused). However, during initial flash programming and verification, it requires an oscillator frequency in the range 24 MHz to 3 MHz. That datasheet also answers many other questions you might have about this microcontroller.


What word is used to express frequency?

kHZ or HZ or MHZ


What will happen if crystal frequency of 8085 is increased from 5 to 20 MHz?

Since the 8085 has a maximum clock frequency of 6 MHz, increasing the crystal frequency from 5 MHz to 20 MHz, a corresponding clock frequency change of 2.5 MHz to 10 MHz, the chip would malfunction.


What is operating frequency of microprocessor?

The operating frequency of 8085 is 3 mhz to 5 mhz


What frequency range is the Very High Frequency band?

30 MHz to 300 MHz


What word is used to describe frequency?

Hertz khz, Mhz etc.......


What unit is used to measure the frequency of memory?

This unit is megahertz (MHz).


What is uplink frequency in gsm?

GSM 900: Uplink frequency: 890 - 915 MHz GSM 1800 : Uplink frequency: 1710 - 1785 MHz GSM 1900: Uplink frequency: 1850 - 1910 MHz


What is a measurement of frequency of a bus and cpu?

A system bus frequency is 1600 MHz. A CPU frequency is 166 MHz to almost 4GHz.


What is frequency band for FM?

30 Mhz - 300 Mhz


What is the components of intermediate frequency amplifier?

Commonly used intermediate frequencies110 kHz was used in Long wavebroadcast receivers. [1]Analoguetelevision receivers using system M: 41.25 MHz (audio) and 45.75 MHz (video). Note, the channel is flipped over in the conversion process in anintercarriersystem, so the audio IF frequency is lower than the video IF frequency. Also, there is no audio local oscillator, the injected video carrier serves that purpose.Analoguetelevision receivers using system B and similar systems: 33.4 MHz. for aural and 38.9 MHz. for visual signal. (The discussion about the frequency conversion is the same as in system M)FM radioreceivers: 262 kHz, 455 kHz, 1.6 MHz, 5.5 MHz, 10.7 MHz, 10.8 MHz, 11.2 MHz, 11.7 MHz, 11.8 MHz, 21.4 MHz, 75 MHz and 98 MHz. In double-conversion superheterodyne receivers, a first intermediate frequency of 10.7 MHz is often used, followed by a second intermediate frequency of 470 kHz. There are triple conversion designs used in police scanner receivers, high-end communications receivers, and many point-to-point microwave systems.AM radioreceivers: 450 kHz, 455 kHz, 460 kHz, 465 kHz, 470 kHz, 475 kHz, 480 kHzSatellite uplink-downlinkequipment: 70 MHz, 950-1450 Downlink first IFTerrestrial microwaveequipment: 250 MHz, 70 MHz or 75 MHzRadar: 30 MHzRF Test Equipment: 310.7 MHz, 160 MHz, 21.4 MHz


What is the name of the acronym MHz?

The acronym MHz stands for megahertz, which is a unit of frequency equal to one million cycles per second. It is commonly used to measure the clock speed of computer processors and the frequency of electronic signals.