answersLogoWhite

0


Best Answer

There are a number of characteristics found in a common emitter amplifier. Not only are the parameters considered, but also their performance. Characteristics and performance are: voltage gain/ medium; current gain/ medium; power gain/ high; input / output phase relationship/ 180 degrees; input resistance/ medium; and output resistance/ medium.

User Avatar

Wiki User

10y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What are the characteristics of a common emitter amplifier?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Music & Radio

What is the Frequency response of common emitter amplifier?

The voltage gain is a measure of the amplified output available at the collector terminal divided by the voltage measured on the base. This if you have 10 mV applied to the base and voltage of 1 volt at the collector the voltage gain is 100ANSWERThe maximum voltage gain of a common emitter amplifier is dependant on the transistor itself. Some have only a very small voltage gain such as in Radio Frequency Power transistors. These are almost all used as common emitter circuits for bipolar transistors or common source for FETs.. On the other hand some darlington transistors can have common emitter gains of hundreds of thousands. If the stage has an unbypassed emitter resistor, the voltage gain is equal to Rload/RE, (Rload is the parallel value of the resistance from collector to the supply and the resistance of the load).If the emitter resistance is bypassed, the value of resistance to be used for RE is the internal Re which is equal to 25mV/Ie


Why biasing is needed at all?

Biasing is used in a transistor amplifier circuit in order to place the transistor as nearly as possible in the center of its linear region. Transistors have cutoff, linear, and saturation regions. Too little bias current, and you enter cutoff - Too much, and you saturate. Both conditions cause distortion when you attempt to use the transistor as an amplifier, as opposed to a switch.


How should the two transistor junctions be biased for proper transistor amplifier operation?

Emitter-Base junction should be forward biased.Collector-Base junction should be reverse biased.


Which transistor configuration is mostly used?

common emitter configuration is use for amplification purpose while common collector is use as buffer as its op is same as ip..


What is the best tube acoustic amplifier?

whats the best tube acoustic amplifier ?

Related questions

Why base in grounded in common emitter transistor as amplifier?

With a common emitter amplifier it's the emitter that is usually grounded.


What is Ce amplifier?

A: REFERS TO A common emitter amplifier


What is the effect of emitter resistance in common emitter amplifier?

The gain of a common-emitter amplifier is collector resistor divided by emitter resistor, or hFe, whichever is less. Since hFe depends on temperature, designing the amplifier to be dependent on resistance ratio makes it more stable. As such, the emitter resistance serves to stabilize the amplifier.


What is the difference between a CB amplifier and CE and emitter-follower?

I think you mean a common emitter amplifier, which is an amplifier of voltage. Emitter-follower or common collector amplifiers are used to match impedances, or to amplify power or current. The emitter-follower is a type of common emitter circuit that has a resistor between the emitter and ground. The output signal is taken from the point between the emitter and its resistor.


What are different names of CE amplifier?

what is the other name of common emitter amplifier


What is the advantage of common emitter amplifier?

Itamplifiesthe gain


What configuration commonly employed in bipolar transistor amplifier?

Common Emitter - Class A Amplifier.


What is the effect on voltage gain in a common emitter amplifier when the decoupling capacitor is removed?

The emitter bypass capacitor, in a typical common emitter configuration, increases gain as a function of frequency, making a high pass filter. Removing the capacitor will remove the gain component due to frequency, and the amplifier will degrade to its DC characteristics.


What is the other name for the common-collector amplifier?

emitter follwer


Why there is 180 degrees phase shift in common emitter amplifier?

In the common emitter amplifier, an increase of base-emitter current causes a larger increase of collector emitter current. This means that, as the base voltage increases, the collector voltage decreases. This is a 180 degree phase shift.


How do you draw thevinin equivalent circuit of common emitter amplifier?

bbc


Why common emitter is considered as best?

b'cose the gain of the amplifier is high ..