Water isn't bad for a plastic or hard rubber mouthpiece. Hot water can discolor a hard rubber mouthpiece, so keep it cool. Mild soap won't hurt it either. Use a medium-soft brush on the outside and a cone-shaped mouthpiece brush in the inside. Be careful about the cork. I wrap the cork with plumbers Teflon tape before cleaning to protect it. Also be careful with the tip of the cone-shaped internal brush that you don't inadvertently chip the tip of the mouthpiece by brushing to vigorously. If it is a vintage wood mouthpiece, all bets are off!
Yes, because the kettle will melt. but you can get plastic kettles that are safe to boil your water in. so when it shows signs of melting that means you have to replace it
Plays the kettle?A kettle drum is played by a percussionist.A kettle (for boiling water) can have a mouthpiece fitted and be played as a wind instrument, like the brass section of an orchestra.
There are many ways you can clean your G pen mouthpiece. You can use cleaning solution or even soap and water.
The best way to remove a mouthpiece is with a mouthpiece puller. Most music stores will have a puller, and some will even pull mouthpieces for free. You will get a lot of other suggestions on how to pull the mouthpiece. The problem is, if you use pliers or other inappropriate tools, even with padding of some kind, you can damage the trumpet. The only relatively safe way to try it yourself is to hold the trumpet's mouthpiece tube (ahead of the mouthpiece) under the hot water tap for a couple of minutes. While doing this, hold a package of frozen vegetables, or the like, around the mouthpiece. The idea is to get the mouthpiece as cold as possible, and the pipe as warm as possible. Then, using a hot pad, try to extract the mouthpiece. This may or may not work (it does most of the time) but if it doesn't, it causes no harm to the trumpet.
Yes noodles do expand when you add water well boiling water any way
Yes but hardly measurable. Boiling water is only 212 degrees F.
Because heat makes plastic expand in hot water.
Yes, pouring boiling water into a plastic bottle can be dangerous as the high temperature can cause the plastic to release harmful chemicals into the water. This can lead to contamination of the water, which may not be safe to consume. It is best to use containers that are specifically designed for hot liquids.
Water isn't bad for a plastic or hard rubber mouthpiece. Hot water can discolor a hard rubber mouthpiece, so keep it cool. Mild soap won't hurt it either. Use a medium-soft brush on the outside and a cone-shaped mouthpiece brush in the inside. Be careful about the cork. I wrap the cork with plumbers Teflon tape before cleaning to protect it. Also be careful with the tip of the cone-shaped internal brush that you don't inadvertently chip the tip of the mouthpiece by brushing to vigorously. If it is a vintage wood mouthpiece, all bets are off!
No, so you will want to leave an inch or two when filling the bottle as well as leaving it uncovered until the water has frozen.
If a balloon is placed above boiling water, the heat from the water will cause the air inside the balloon to expand. The balloon will likely inflate and may eventually burst if the heat is not removed or the balloon is not released.
if you mean a mouthpiece yes, dip in boiling water for 35 sec. then dip in cool water not ice water for 3 sec. bite down then in the boiling water for 10 sec. then cool water for 1 sec. and bite down and press you tongue up and pus it against your teeth
plastic container exposed to boiling water?
Placing a dented table tennis ball in boiling water causes the air inside the ball to expand, pushing out the dent and restoring the ball's shape. The heat softens the plastic material of the ball, allowing it to return to its original state. Once the ball cools down, it retains its new shape.
A piece of plastic over a boiling kettle will collect the steam (evaporated water) and it will condense.
When Styrofoam balls are placed in boiling water, they will start to melt and deform because Styrofoam is a type of plastic that softens under heat. The heat causes the air pockets in the material to expand and the balls to lose their shape, resulting in a gooey mass. Additionally, the release of toxic fumes from the melting Styrofoam can be harmful if inhaled.