a series resistence with its coil
There are a couple of examples that come to mind where there is a coil in a circuit. One is, the coil is used as a choke to block harmonics from going down the electrical line. Another example of a coil in the line is the coil in a magnetic contactor. When this coil is energized the contacts of the magnetic contactor close.
A1 drawing boards are mostley used for builders when designing houses or small scale shops they are not used for huge scale developments.
The pointer on a galvenometer moves due to magnetic force between the current carrying coil in the pointer assembly and the permanent magnet surrounding that coil.
A linear meter is exactly the same as a meter. So, 3000 linear meters = 3000 meters. "Linear" is just an unnecessary adjective to be used only if there is some doubt whether you are refering to a length (meter, m), area (square meter, m2) or volume (cubic meter, m3).
Moving coil instruments are commonly used as voltmeters and ammeters in electrical circuits. The moving coil inside the instrument responds to the current passing through it, deflecting a needle on a scale to provide a measurement of voltage or current. These instruments are known for their accuracy and reliability in measuring electrical quantities.
Most meters use a moving coil meter movement, which utilizes a coil of wire attached to a needle that moves in response to the current flowing through the coil. This movement is reliable and accurate for measuring various electrical quantities.
Concave mirrors are used in moving coil galvanometers to magnify the deflection of the coil. The concave mirror reflects the light beam onto a scale, making it easier to measure small deflections accurately. This setup increases the sensitivity and precision of the galvanometer.
A coil galvanometer is a type of device that uses a movable coil in a magnetic field to measure electric current. As the current flows through the coil, it experiences a torque that causes it to move, with the deflection indicating the strength of the current. These galvanometers are used in applications such as measuring small currents, detecting the presence of current, and in analog meter movements.
Weston frequency meter is a type of electromechanical instrument used for measuring the frequency of an alternating current (AC) power system. It typically consists of a moving-coil meter mechanism that reacts to the frequency of the AC signal to provide a reading on its scale. Weston frequency meters are used in various applications to monitor and analyze the frequency of electrical systems.
a series resistence with its coil
A moving-coil ammeter is an analogue ammeter, used to measure direct current. It works on the same principle as an electric motor, whereby a pivoted coil, located between the two poles of a horseshoe magnet, will rotate when current is passed through it. The movement is restricted by a pair of hairsprings, which means that the moving coil will move through an angle that is proportional to the current. A pointer, attached to the coil, sweeps across a suitably-graduated scale, to indicate the value of current passing through the coil.
Yes, but with vey low sensitivity and poor frequency response.
Some examples of galvanometers include moving-coil galvanometers, moving-magnet galvanometers, and digital galvanometers. These devices are used to measure small electric currents through the deflection of a needle or pointer on a scale.
For moving-iron instrument magnetic field is caused when the current (voltage) passes the fixed circle. When the current (voltage) passes the fixed circle,the two iron plates are magnetized ,rotational torque is resulted, the deflection angle indicate measured current. Because the magnetized polarity is same for AC or DC, moving-iron instrument can be used in AC and DC circuit. For permanent-magnet moving-coil instrument magnetic field is caused by the permanent-magnet, When the DC current passes the moving coil, rotational torque is resulted,so the deflection angle indicate measured DC current. As AC current passes the moving coil ,because inertia of moving parts of meter the deflection angle indicate rotational torque average, but rotational torque average is zero in cycle, moving parts of meter is´t deflec,so permanent-magnet moving-coil instrument only is used in DC circuit.
The main part of a scale meter is the scale itself, which consists of markings and numbers that indicate measurement units. The scale is used to accurately measure weight or other quantities.
It is used for measuring distances or lengths.