answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: How grease pump works?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Mechanical Engineering

How does axial pump works?

An axial flow pump operates centrifugally in design. The fluid is pushed outward from the center or axis of the pump.


Grease similar to kluber asonic GHY72 grease?

I HAVE A 15KW 50Hz 400V VEM MOTOR , I WANT TO RENEWAL THE GREASE


How concrete pump works?

A concrete pump which comprises an elongated hollow housing in which a valve element reciprocates. The valve element includes a pair of transversely extending tubes and a pair of concrete guiding chambers. The valve element moves between two positions. In the first position a first guide chamber is opposite a first pump cylinder and guides concrete from an upright conduit associated with the first pump cylinder into the first pump cylinder and a first tube is opposite a second pump cylinder and guides concrete from the second pump cylinder into a discharge line associated with the second pump cylinder. At the second position a second guide chamber is opposite the second pump cylinder and guides concrete from an upright conduit associated with the second pump cylinder into the second pump cylinder and the second tube is opposite the first pump cylinder and guides concrete from the first pump cylinder into the discharge line associated with the first pump cylinder.


What kind of shell grease is the same as unirex N2?

Wicth shell grease can be equivalent with Mobil Unirex N 3?


Types of positive displacement pump?

gear pump, crescent gear pump, axial-piston pump, radial-piston pump, linear-piston pump, & vane pump Also, fuel injection pumps such as linear piston pumps and rotary piston pumps.

Related questions

How much does one pump of grease weigh from a grease gun?

In a pistol grip grease gun each pump weighs 33 grams.


What equipments are used for wellhead maintenance?

General equipment are : Hydraulic tool to open and tight studs, grease pump, stinger to check pressure in the cavities, VR plug lubricator, BPV lubricator, air compressor, heavy grease hand pump, hand pump, BPV, TWCV. Grease, Ring gaskets, bearing grease pump ...


What is a grease fitting?

a grease fitting is something that u put a grease gun into and pump grease into it to lubricate ball joints, steering knuckles ect...


How do you prime a 2.2 Toyota Camry oil pump?

many engine builders like to use lubriplate 105 assembly grease pack clean grease into inlet of pump for start up or if pump is open pack clean grease into gears or lobe and rotor


How do you get s?

You can get an S-Curl by using a certaint grease light grease works best.


What grease remover works best?

Dry cleaning usually removes grease stains.


How do you get a S-curl?

You can get an S-Curl by using a certaint grease light grease works best.


Why did they nickname the M3 machin gun the Grease Gun?

It has a superficial appearance similar to the tool that was used by mechanics to pump grease into fittings on cars, and that tool is called a grease gun.


How do you get greasey work clothes cleaner?

use the grease remover that you use to get the grease off your hands it really works:]


How do you change the fuel pump in a 327 Chevy Small block Think it is 1968?

it is located on right front of block. First remove your fuel lines, the remove the retaining bolts holding it on the pin will slide out after the pump. coate the pin with grease and reinstall in its hole(grease will hold it for you so you can get the pump in) the install pump and lines


How do you remove large quantities of grease from grease trap drain?

Mechanically: scoop it up into a bucket. If it is liquid you can pump it but if it too thick then you got to shovel it out.


When changing the fule pump on an 1983 Chevy 350 what about the push rod that runs the pump will it fall out and is there any way to hold it in place?

You can put grease on the rod and gently push it into the block. the grease will hold it in place for a good amount of time.