0
first check all your tires pressure. then park the mower on a level concrete surface and drop the deck to the ground. then reach up under the frame but above the deck in front of each back tire and loosen the big wing nut. do this on both sides. then go to the deck height adjuster and pull the plastic cover off the lower end slots and lower the handle all the way down and lock it in. now all you have to do is tighten the wing nuts under the frame and then pull up the height adjuster handle and you have leveled the deck. one more thing if your deck has gage wheels on it you really need to take them off for this leveling job
Park on a flat, level concrete surface. Remove the cutter deck gauge wheels, lift the extra plastic flap below the cutter deck height lever, place a 2x4 wooden block under each side of the cutter deck. The blocks should be at the outer most point of the deck. With the flap raised, move the height lever to the lower most position. Loosen the plastic wing nuts (one on each side)and the spring loaded brackets should move to a neutral position, leveling the deck based on the blocks under the deck. Retighten the wing nuts, raise the deck lever to a position above the extra flap. Fasten the flap, remove the blocks, reinstall the gauge wheels, and you are good to go.
Add your answer:
Earn +20 pts
How do you put a belt on a murry riding cut?
Hard to answer without a deck size.
Do you have a picture of routing a drive belt on a mower deck?
john deere LT155 38inch cut mower deck
Why does your riding lawnmower cut unevenly?
Two most common reasons are (1) low tire(s) and (2) mower deck not level. Low tire being the main and most common.
How do you adjust the cutting level of a MTD riding mower even at the highest setting its scalping my yard?
how do u adjust deck on yard machine made by mtd 42 inch cut 16,5 horse
Belt size for yard machine riding mower 20 hp 46 in cut?
what size is the belt for a 46 in cut deck belt with 6 pulley's.
42 inch Murray mower engage deck won't cut grass?
The belt is too loose. Replace it or adjust the idler.
Belt diagram for a 46 inch tri cut noma lawn mower?
Belt diagram for brings&straton noma 46" deck
How do you install belt to mowing deck on 42 cut Murray 15.5 riding lawnmower?
I have Murray 42" cut riding mower that the belt came off. How do I put the belt back on?
How do you level cutting deck on Murray model 40712X99A lawn tractor?
Per the owners manual for the tractor:HOW TO LEVEL THE MOWER HOUSINGIf the mower housing is level, the blades will cut easier and the lawn will look better.1. Make sure the unit is on a hard, flat surface.2. Check the air pressure in the tires. If the air pressure is incorrect, the mower will not cut level. Make sure the tires are inflated to 14 PSI (1 BAR).3. Some models have gauge wheels on the mower housing. If equipped, remove the gauge wheels.4. Open the [lift lever] cover.5. Move the lift lever to the LEVEL ADJUSTMENT position.WARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUSTMENT position.6. Loosen the left and right adjuster knobs. Push down on each side of the mower housing. Make sure both sides of the mower housing are setting on the flat surface.7. Tighten the left and right adjuster knobs.8. Raise the left lever from the LEVEL ADJUSTMENT postition to a CUTTING HEIGHT position.9. Close the cover.10. If equipped, install the gauge wheels.11. Mow for a short distance. If the height of the cut is not level, repeat the above steps.CAUTION: Do not operate with the mower housing in the LEVEL ADJUSTMENT position. If you operate in the LEVEL ADJUSTMENT position, the mower housing and blades can be damaged.####
What is the advantage of 3 blade mower deck verses a2 blade?
It will give you extra cutting width with out increasing the front to backdimension . In other words you can have a 72" cut without having a deck that is 36" front to back.
How do you align blades on a 46 inch mower deck?
Without knowing the exact mower you are working on, I will give you the most common answer. If the blades are belt driven you do not have to align them. They are positioned so that they will not contact each other and will overlap in their cut pattern.
What is the purpose of a Flail mower?
The purpose of a Flail mower is to cut tougher, thicker grass that can not be cut by an ordinary mower. They are usually driven and often used to cut grass by roadsides.
