0
Add your answer:
Earn +20 pts
What is the bevel degree onbutt weld fittings?
between 30 and 40 degrees preferably 37 like pipe
What is the filet weld size required for weldolets to main pipe joint?
wildly welding main pipe the are fillet weld or butweld
Butt-weld and grrove weld?
First, Butt-weld is short for a butt groove. Welding in a butt-groove starts at the throat of the butt-groove. The first weld point could be a tack-weld: holding the two materials to be welded together. The throat is measured and filler metal and electrode are determined to create the root pass.
What is ERW pipe means?
Electric resistant weld
How do you weld fitting a234 with pipe api 5l x60 w th11.9 mm?
The step-by-step instructions on how to do a weld fitting on a A234 with a pipe of API 5L x60 w TH11.9 mm is not listed. It might be best to purchase a weld fitting manual for a A234 for further information.
What is the bevel degree onbutt weld fittings?
between 30 and 40 degrees preferably 37 like pipe
What is root pass?
It is the first pass in a multiple weld joint.
What is a root pass?
It is the first pass in a multiple weld joint.
When welding a single bevel butt joint which side should be welded first?
You always weld the side with the preperation first, then if you get incomplete penetration you can grind the back out
How much bevel angle shoul be there in between butt weld?
27.5 degrees
Is it ok to weld gi pipe?
Gi weld not recommended . Because of gi coationg will be spoiled out . Puncture will be occur on the pipe weld .
Can gi pipe weld with ms?
Very likely to leak, zinc in the GI pipe will be contaiminating the weld and thus you cannot get a good weld.
What is the first weld called when you are welding two beveled pieces of pipe?
tack
What the difference between weldolet and thredolet?
A weldolet is a fitting you weld on a (run) pipe, and then butt weld a branch pipe to it. A tredolet is a fitting you weld on a (run) pipe, and then screw a threaded branch pipe to it. Some people call this a threadolet A sockolet is a fitting you weld on a (run) pipe, and then socket weld a branch pipe to it. A nipolet is the same as a weldolet or thredolet but has an elongated branch connection. You have to specify if it's a welded or threaded nipolet.
In the 5G position for welding pipe the pipe must?
The pipe must be fixed (not rolled) in the horizontal position. With the pipe horizontal, the weld is vertical. The pipe being fixed requires the welder to weld flat (top), vertical (sides), and overhead (bottom). The pipe must be fixed (not rolled) in the horizontal position. With the pipe horizontal, the weld is vertical. The pipe being fixed requires the welder to weld flat (top), vertical (sides), and overhead (bottom).
What is the filet weld size required for weldolets to main pipe joint?
wildly welding main pipe the are fillet weld or butweld
What is the difference between a Butt weld and a socket weld?
A butt weld is where the diameter of the pipes welded together are the same, a socket weld is where a larger diameter pipe is fitted into a smaller one. In making a butt weld, the pipes (or pipe and fitting) usually have an angle machined or ground into the outside corner, so when they are placed together face-face, there is a circumferential V shaped gap serving as the weld prep. In a socket weld, the pipe is inserted into the socket, backed off slightly to make a gap between the end of the pipe and the bottom of the socket, and the weld is made around the outside diameter of the socket to the outside diameter of the pipe. The gap at the bottom of the pipe prevents thermal expansion from stressing the joint during or after welding.
