0
Add your answer:
Earn +20 pts
Where is the IAT sensor at?
The IAT sensor measures the temperature of the intake nmanifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have found improvement in EGT, fuel economy, and power after cleaning carbon from the IAT sensor in at the rear of the intage manifold. Engine with exhaust brakes are particularly prone to IAT sensor fouling because soot is blown back into the intake during valve overlap. The only tool you need is a 3/8" ratchet with a 6" extension and 13/16" socket. View of IAT from above battery Closer view of the IAT sensor The IAT sensor is found on the driver's side of the engine, almost at the back of the intake manifold. Unplug the electrical connector from the sensor. You will need to spread the connect tab away from the sensor body to unplug the sensor. After the connector has been removed, use a 13/16" deep well socket, 6" extension, and ratchet to unscrew the sensor from the manifold. Photo of a dirty IAT sensor The sensor on the left had 20,000 miles on it, and it was covered with soot. After a shot of carburator cleaner, you can see the sensor element inside the cage. Screw the clean IAT sensor back into the manifold, torque it to 10 ft-lb, and reattach the connector. Photo of a clean IAT sensor Normal IAT Sensor resistance values: Temperature Resistance 30� 40K 32� 30k to 36k ohms 76� 13K ohms 77� 9k to 11k ohms 81� 6.87K ohms 122� 3k to 4k ohms 130� 4K ohms 167 600 to 675 ohms 212 600 to 675 ohms Replacement Sensor: Cummins PN 3408345, around $28. Dodge PN 05014197AA Sensor, Temperature (SEN, TEM), around $18.
Where is Iat sensor at?
The IAT sensor measures the temperature of the intake nmanifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have found improvement in EGT, fuel economy, and power after cleaning carbon from the IAT sensor in at the rear of the intage manifold. Engine with exhaust brakes are particularly prone to IAT sensor fouling because soot is blown back into the intake during valve overlap. The only tool you need is a 3/8" ratchet with a 6" extension and 13/16" socket. View of IAT from above battery Closer view of the IAT sensor The IAT sensor is found on the driver's side of the engine, almost at the back of the intake manifold. Unplug the electrical connector from the sensor. You will need to spread the connect tab away from the sensor body to unplug the sensor. After the connector has been removed, use a 13/16" deep well socket, 6" extension, and ratchet to unscrew the sensor from the manifold. Photo of a dirty IAT sensor The sensor on the left had 20,000 miles on it, and it was covered with soot. After a shot of carburator cleaner, you can see the sensor element inside the cage. Screw the clean IAT sensor back into the manifold, torque it to 10 ft-lb, and reattach the connector. Photo of a clean IAT sensor Normal IAT Sensor resistance values: Temperature Resistance 30� 40K 32� 30k to 36k ohms 76� 13K ohms 77� 9k to 11k ohms 81� 6.87K ohms 122� 3k to 4k ohms 130� 4K ohms 167 600 to 675 ohms 212 600 to 675 ohms Replacement Sensor: Cummins PN 3408345, around $28. Dodge PN 05014197AA Sensor, Temperature (SEN, TEM), around $18.
Where is the IAT sensor located?
The IAT sensor measures the temperature of the intake nmanifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have found improvement in EGT, fuel economy, and power after cleaning carbon from the IAT sensor in at the rear of the intage manifold. Engine with exhaust brakes are particularly prone to IAT sensor fouling because soot is blown back into the intake during valve overlap. The only tool you need is a 3/8" ratchet with a 6" extension and 13/16" socket. View of IAT from above battery Closer view of the IAT sensor The IAT sensor is found on the driver's side of the engine, almost at the back of the intake manifold. Unplug the electrical connector from the sensor. You will need to spread the connect tab away from the sensor body to unplug the sensor. After the connector has been removed, use a 13/16" deep well socket, 6" extension, and ratchet to unscrew the sensor from the manifold. Photo of a dirty IAT sensor The sensor on the left had 20,000 miles on it, and it was covered with soot. After a shot of carburetor cleaner, you can see the sensor element inside the cage. Screw the clean IAT sensor back into the manifold, torque it to 10 ft-lb, and reattach the connector. Photo of a clean IAT sensor Normal IAT Sensor resistance values: Temperature Resistance 30� 40K 32� 30k to 36k ohms 76� 13K ohms 77� 9k to 11k ohms 81� 6.87K ohms 122� 3k to 4k ohms 130� 4K ohms 167 600 to 675 ohms 212 600 to 675 ohms Replacement Sensor: Cummins PN 3408345, around $28. Dodge PN 05014197AA Sensor, Temperature (SEN, TEM), around $18.
Where can you specifically locate the IAT sensor on a 98 Dodge Durango?
it's on top of the engine close to where the thermostat is.it does have two wires 18 or 20 ga.
Timing belt snapped on y reg 1.2 clio how much to fix?
it would have to fix about 3.9 gallons of gasoline to get a 18 wheeler truck
Whats the price for a o2 sensor?
You will have to call a parts store for the price. I have a Chev car and it was $18 and I have a Chev truck and the sensor was $ 100.
Were is the rev counter sensor on a mk4 18 16v astra sport?
Check the earth on your inlet manifold. The pick-up is part & parcel of the engin "KNOCK SENSOR"!
Where is the intake air temperature sensor in a 98 passat 18 t?
Just after the throttle body
Where is the speed sensor on a 1990 Cadillac deville?
The speed sensor for a 1990 Cadillac Deville is located on the side of the transmission. Look for a 2 wire plug with 18 gauge wire.
4m41 mitsudishi pajero trouble code 18 NE snsr sub?
The pump cover has 2 sensors. Lower sensor on side is sub technology sensor. On top is main sensor. Yes they go bad just replace.
What is the thread size of oxygen sensor on a 2000 rx 300 Lexus?
18 Millimeter, 1.5 Pitch
What is the tap size for the O2 sensor for a 1998 S10 truck 4 cylinder?
The mechanic said that it was an 18 mm x1.5.
