0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you reset the service light in a 2004 Volvo S80?
1. Turn ignition switch to position I. 2. Press and hold "day counter reset button". 3. Turn ignition to position II. 4. Continue holding day counter for about 10 seconds. 5. While SRL flashes, release day counter button. 6. Should hear "beep-beep" to confirm command accepted.
Not the check engine light but the service light on the 1998 s60 Volvo?
Volvo 1999-2000 - S / V / C70 Models * Press and Hold odometer reset button * Turn ignition switch to "run" position * After SRL flashes, release odometer reset button * Turn ignition off * Turn ignition back on to confirm reset Volvo 1998 - S80 Models * Turn ignition switch to position 1 * Press and hold the odometer reset button * Turn ignition switch to position 2 * Wait until service light blinks and then release odometer button Volvo 1999-2000 - S80 Models * Turn ignition switch to position 1 * Press and hold "day counter reset button" * Turn ignition switch to position 2 * Continue holding day counter for approx. 10 seconds * After SRL flashes, release day counter button * Should hear "beep-beep" to confirm command accepted Volvo 2001 - XC 70 Models * The following steps must be completed with no longer than 5 seconds between each step: * Make sure the trip meter is in T-1 * Turn ignition key to position 1 * Press and hold trip meter button until zero is shown * While still holding the trip meter, turn key to position 2 * When original trip mileage returns, release the trip reset button * Turn key to off
How will you reset the service light on a 97S70 Volvo?
dealer only**edit**This is not true. dealerships want you take them your car and charge you a 95.00 service fee to do this. here is the procedures for some cars.Volvo 1999-2000 - S / V / C70 Models * Press and Hold odometer reset button* Turn ignition switch to "run" position* After SRL flashes, release odometer reset button* Turn ignition off* Turn ignition back on to confirm reset Volvo 1998 - S80 Models * Turn ignition switch to position 1* Press and hold the odometer reset button* Turn ignition switch to position 2* Wait until service light blinks and then release odometer button Volvo 1999-2000 - S80 Models * Turn ignition switch to position 1* Press and hold "day counter reset button"* Turn ignition switch to position 2* Continue holding day counter for approx. 10 seconds* After SRL flashes, release day counter button* Should hear "beep-beep" to confirm command accepted Volvo 2001 - XC 70 Models * The following steps must be completed with no longer than 5 seconds between each step: * Make sure the trip meter is in T-1* Turn ignition key to position 1* Press and hold trip meter button until zero is shown* While still holding the trip meter, turn key to position 2* When original trip mileage returns, release the trip reset button* Turn key to off
How can you reset the Citroen C4 service light?
Press day-counter and then turn on the ignition key. You will the 10 seconds countdown (where you normally see the mileage counter). After the countdown the reset is completed.
Does top contributors counter reset monthly on WikiAnswers or the first of each month or from that day on the previous month?
The list are reset at the start of the month.
How do you set time on a aw61790w?
To set the time on a AW61790W watch, start by pressing and holding the "Set" button until the seconds start blinking. Use the "Mode" button to switch between hours, minutes, and other settings. Use the "Adjust" button to change the values. Once you've set the time, press "Set" again to confirm.
How do you reset time date day on atomix clock00582a1?
To reset the time, date, and day on an Atomix clock model 00582A1, locate the "SET" button on the clock and press it until the display starts blinking. Use the arrow buttons to adjust the time, date, and day accordingly. Once set, press the "SET" button again to save the changes.
How do you stop the hourly beep on a aw60447w watch?
Hourly chime on/Off: 1.) Press and hold the lap/reset button (bottom right) to display alarm time 2.) While holding lap/reset button, press the mode button (bottom left) 3.) If the all the day of week indicators our lit, beep is on. If they are all off, beep is off. Alarm On/Off: A press of the lap/reset button (labeled) will show the alarm time, Unpress will show the time of day. Press again toshow the alarm time. Press and hold the lap/reset button will show the alarm time again, but it will hold there. While holding this lap/reset button, press the start/stop button (labeled). This will turn on (or off) the alarm (tiny indicator). Press this start/stop button repeatedly (while still holding the lap/reset button and you will see the indicator turning on and off with each press. Stop this button pressing with the indicator OFF, let up on the lap/reset button, and the time will return to the screen. The alarm will now be OFF.
How do you set the time on a cardinal WR50M?
Hold the adjust button then click the mode button until you see the (wrong) time. Then to change the numbers just keep clicking the split.reset button. You can also change the date and day by doing one at a time. To set the time, date, or day of the week press start.stop.
How do you change the time on your Armitron digital watch?
I have an Armitron All-Sport digital watch 45/6963 watch with three buttons. Okay, so there are three buttons. One is Mode(Bottom left), one is Reset (Bottom Right) and one is St/Stp (Top right).1. Remember the what time your watch says it is.2. Click and hold the Mode button down for approx. 10 seconds.3. If the hour part is flashing, this should be the alarm time. Click the mode button once, and the screen should change, so it says the time that it said on your watch before.4. The seconds spot should be flashing now. To start the seconds at 00, press the reset button (Bottom right).5. Then, click the St/Stp button to be able to change the minutes. The minutes part should be flashing now. Just click the Reset button(Bottom right) to change the minutes.6. To be able to change the hour, click the St/Stp button(top right). Now, the hour part should be flashing, and there should either be an A for A.M. or a P for P.M. where the seconds used to be. Now, just click the reset button(BottomA(A.M.) or P(P.M.) so when it's 11:00 A.M. your watch won't think ti's 11:00P.M.right) to change the hour.7. To set the day of the week, click both the St/Stp button, and the reset button at the same time. The screen should just have 2 numbers showing. The hour should be flashing right now. Click the St/Stp button twice. Now, the day of the week at the top should be flashing. To change the day of the week, simply click the Reset button until you have the right day of the week.8. Finally, to set that as your time and day of the week, click the Mode button(bottom left), and it should now show the time and day of the week you set it for!I was so glad when I FINALLY figured it out!
How do you set the AW60443W watch?
All you have to do is press the Mode button. It will go to the alarm time first, to change the hour (which should be blinking first), press Start until you get to the correct number. You can move to the minute section pressing the Reset button, then use the Start button to get to the wanted number of minutes. Press mode repeatedly until you get to the time of day and then you can do the same (seconds can only go back to :00). Also do this for the date. When you have the correct time press Mode again and you will get back to the normal time of day screen.
How do you set a Charles Raymond solar power watch?
To set the time 1. Hold the reset button until the hour mode (12/24) is flashing 2. Press the mode button to scroll (year, month, day, hour) 3. Use the ST/STP button to advance 4. Press reset button to return to normal operation To set the alarm 1. Press the mode button to scroll to AL1 mode 2. Press the reset button to scroll through the 3 alarm modes 3. When alarm mode is displayed hold the reset button until the time is flashing 4. Use the ST/STP button to advance 5. Press reset button to return to normal operation Note: To change AM to PM you must advance through a complete 12 hour cycle.
