Temperature affects the resistivity of materials which, in turn, affects their resistance. For pure metal conductors, their resistance increases with temperature. As an inductor is often made from a coil of copper wire, its resistance will increase whenever its temperature increases. If it is important for the resistance to remain constant over a wide variation of temperature, then alloys, such as constantin, are used instead of copper. These alloys maintain an approximately-constant resistance over a wide range of temperatures.
Yes, it possible to heat a coil using dc power supply. An inductor resists a change in current, proportional to voltage and inversely proportional to inductance. The equation of an inductor is di/dt = v/L An ideal inductor, if connected to an ideal DC supply, with ideal conductors, would ramp up current in a linear fashion without limit, eventually reaching infinity amperes after infinite time. Since no inductor is ideal, nor is any DC supply, nor is any conductor, the current would reach a maximum based on the capacity of the DC supply and the DC resistance of the inductor and conductors. Since the DC resistance of the inductor is also not zero, this means, by Ohm's law, that the inductor must dissipate some power. That will cause the inductor to heat up.
Yes it does as it is an Inductor and an Inductor needs to build up a magnetic field. It is called INRUSH current.
When your circuit starts up, your inductor creates an electrical current in the opposite direction. With dc, this effect vanished after the circuit is started. With ac, the current keeps starting and stopping so the inductor keeps creating a current in the opposite direction.
An inductor looks like a piece of wire to DC. It will thus look like a resistor, and inductor properties do not apply.
inductor was invented by scientist lenz so it is denoted by l..
Yes, it possible to heat a coil using dc power supply. An inductor resists a change in current, proportional to voltage and inversely proportional to inductance. The equation of an inductor is di/dt = v/L An ideal inductor, if connected to an ideal DC supply, with ideal conductors, would ramp up current in a linear fashion without limit, eventually reaching infinity amperes after infinite time. Since no inductor is ideal, nor is any DC supply, nor is any conductor, the current would reach a maximum based on the capacity of the DC supply and the DC resistance of the inductor and conductors. Since the DC resistance of the inductor is also not zero, this means, by Ohm's law, that the inductor must dissipate some power. That will cause the inductor to heat up.
heat energy
An inductor does not produce heat by itself. However, when an inductor is connected in an electrical circuit, any resistive components in the circuit may generate heat due to the flow of current through them. This heat dissipation is not directly caused by the inductor but can be a result of the overall circuit operation.
tottoo
what is an inductor used for
Since we know that inductance of an inductor depends on the length of inductor by the formula L=muAN*N/l, where l is the length of inductor. So by varying the length of inductor we say that inductance of inductor varies.
Yes it does as it is an Inductor and an Inductor needs to build up a magnetic field. It is called INRUSH current.
When your circuit starts up, your inductor creates an electrical current in the opposite direction. With dc, this effect vanished after the circuit is started. With ac, the current keeps starting and stopping so the inductor keeps creating a current in the opposite direction.
In an ideal inductor, no, there is no voltage induced across an inductor unless the current in the inductor is changing. However, since there are no ideal inductors nor power supplies, eventually an inductor will draw a constant current, i.e. the limit of the power supply; and, since no inductor has zero ohms at equilibrium, that current will translate to voltage.
The resistance of an inductor is low because the wire in the coil offers a relatively low resistance to the flow of electrical current. Inductors are designed to primarily store and release energy in the form of a magnetic field, with minimal dissipation of energy as heat due to resistance.
any conductor wound with few turns can be considered as an inductor
An inductor looks like a piece of wire to DC. It will thus look like a resistor, and inductor properties do not apply.