0
In general, you can install a wattmeter on the primary or the secondary side of a transformer (it depends what you are trying to measure). But if you are conducting an open- and short-circuit test (to find the transformer's losses), then the wattmeter is connected to the primary side because you want to measure the total (primary + secondary) losses and that is only achievable from the primary side.
Add your answer:
Earn +20 pts
Why load is always connected to secondary of transformer?
b'coz at the secondary side large amount of current flow by recarding of active component or other ckt. which is connected to the secondary side so that ckt. is not damage or burned by flowing large amount .. load is connected at the secondary side .AnswerThe 'primary' winding of a transformer is, by definition, whichever winding is connected to the supply, whereas the 'secondary' winding is whichever winding is connected to the load. This does not mean that a load MUST be connected to a transformer, as it will work 'off load' -that is, with no load connected- without any harm.
If a dc voltage of 12v is added to the secondary of step down transformer and rating of transformer is 220 input and 12v output what will be the result from primary of transformer?
Adding a DC voltage to the secondary of a transformer will not have an effect on the primary side, as transformers work on the principle of electromagnetic induction which is based on alternating current. The primary side of the transformer will still operate based on the input AC voltage of 220V. The DC voltage on the secondary side will not be transferred to the primary side.
Why on load or off load tap changer is always connected in the primary side of a power or distribution transformer. And why distribution and power transformer are rated MVA?
The size of any switch depends on current it carries. Your statement is true for step down transformers. The primary is HV hence less current, so the tap changer is on primary side.
Does the fuse on the primary side of a transformer protect the secondary side?
Yes, but it's usual to have fuses on both sides of the transformer.
What is the different between et up and set down transformer?
the difference between a step up transformer and a step down transformer is that, in a tsep up transformer, the voltage secondary is greater than the primary side but in a step down transformer, the voltage secondary is lesser than the primary side
Why you use low power factor wattmeter on primary and unity power factor on secondary side of transformer?
There is no such thing as a 'low power-factor' wattmeter. A wattmeter always reads true power, regardless of the load's power factor.
How can you distinguish the primary from secondaty side on a transformer?
Whichever winding is connected to the supply is the primary winding; whichever winding is connected to the load is the secondary winding.
What is the load side of a transformer?
The load side of a transformer feeds the device, such as a light or motor. It is the output of the transformer. The input, or line side, provides the voltage that is to be transformed, either up or down, to supply the load side.AnswerA transformer's primary winding is connected to the supply voltage, and the secondary winding is connected to the load.
What does the term primary side refer to?
The line side of a transformer that is connected to your source or incoming voltage that you are stepping up or down.
Why does a transformer blow the circuit breaker on the primary side if it is not connected to a load on the secondary side?
A normal transformer should not blow the primary side breaker when it is not connected to a load on the secondary. If it does, something is wrong. Check for shorted or burned windings. Make sure that it is indeed disconnected from the load - it might still be connected to something that is also presenting a fault.
Which side of a transformer is the load connected to?
It is connected to the secondary side.
Why you uluminium on primary side of transformer?
This isn't the case. You can have aluminium or copper on primary or secondary side of a transformer.
Why rated voltage is to be applied to primary for open circuit test?
Open circuit test on a transformer is usually performed to measure the IRON losses.Iron losses are produced due to eddy current and hysteresis losses. In open circuit test, the LV side, generaly the secondary winding, is kept open and the HV side, generaly the primary winding is fed with the rated voltage and frequency. The rated voltage is applied in order to setup normal flux in the transformer, which in return further produces the normal iron losses at rated voltage. the wattmeter connected at the primary side will show the power consumed due to iron losses. this calculation further utilized for determing the efficiency of transformer.
Why load is always connected to secondary of transformer?
b'coz at the secondary side large amount of current flow by recarding of active component or other ckt. which is connected to the secondary side so that ckt. is not damage or burned by flowing large amount .. load is connected at the secondary side .AnswerThe 'primary' winding of a transformer is, by definition, whichever winding is connected to the supply, whereas the 'secondary' winding is whichever winding is connected to the load. This does not mean that a load MUST be connected to a transformer, as it will work 'off load' -that is, with no load connected- without any harm.
In D.C supply the transformer is not connected why?
In a DC power supply a transformer is connected. The only time there would be no transformer used would be if the DC voltage wanted was 120 VDC. The transformer in the power supply is connected to 120 VAC on the primary side and the secondary side of the transformer is connected to either a half wave or a full wave diode bridge. The voltage out of the diode bridge will be the same output voltage potential as the transformer's secondary voltage but it will be a DC (Direct Current) potential.Reading the question in another way, transformers are not connected in a DC circuit. The reason being is that the transformer operates on a collapsing magnetic field. This field induces a voltage into the secondary side of the transformer. Since the DC circuit does not operate on the principle of a collapsing field except when the circuit is opened, the transformer would not operate as a transformer should..
If a dc voltage of 12v is added to the secondary of step down transformer and rating of transformer is 220 input and 12v output what will be the result from primary of transformer?
Adding a DC voltage to the secondary of a transformer will not have an effect on the primary side, as transformers work on the principle of electromagnetic induction which is based on alternating current. The primary side of the transformer will still operate based on the input AC voltage of 220V. The DC voltage on the secondary side will not be transferred to the primary side.
Why on load or off load tap changer is always connected in the primary side of a power or distribution transformer. And why distribution and power transformer are rated MVA?
The size of any switch depends on current it carries. Your statement is true for step down transformers. The primary is HV hence less current, so the tap changer is on primary side.
