0
I would say because there has to be a standard method of installing flanges that everyone needs to follow. For the simple reason when installing or replacing items such as valves with welded or otherwise fixed flanges, if there was no standard the replacement valve would be 1/8 of a turn or 45 degrees off center if the piping flange bolt holes were on the verticle and the valve flange bolt holes were not. This would be in the case of 4 or 8 bolt flanges.Also in the case of non flanged valves where long bolts pass thru both flanges and squeeze the valve to make the seal a vertically placed bolt hole would interfere with the valve operator or handle preventing the valve from being mounted straight up, down or horizontally.
Add your answer:
Earn +20 pts
What is Difference Between FF & RF Flanges?
Flanges are an integral part of the Piping industry. These Flanges are used to form a link between two different Pipes. Flat (FF), elevated (RF), ring joint (RTJ), lap joint (M&F), tongue, and groove (T&G) are the 6 styles of flange faces needed. Multi-faced flanges need different gaskets and should never be matted to avoid joint leakage. The flanges RF and FF may have various finishing forms (i.e. roughness at the top of the surface): flat, lined, and serrated. Although flanges themselves have specific pound scores that reflect the levels of pressure and temperature to which they can operate, the individual flange faces vary depending on the context within which they are to be used.Various types of flange faces are used to seat the sealing gasket content as the contact surfaces. The faces are panels which matt with flanges, funnels or valves. Flange faces must be smooth enough to ensure that the flanges are fastened together to maintain a stable, leak-free seal. For this article, we must concentrate on three common types of flange faces; flat faces raised faces, and ring-style joints.Flat Face Flanges (FF)The flat-facing flange has a gasket surface in the same plane as the face of the bolt frame. Goods using flat face flanges are often those in which mold is used to make the matching flange or flanged cover. Flat face flanges should never be placed on an inverted side flange. ASME B31.1 notes that the raised face on the carbon steel flange must be removed while attaching flat face cast iron flanges to carbon steel flanges and that a full face gasket is needed. This is to prevent the small, brittle cast iron flange from splashing into the void created by the carbon steel flange’s raised nose.This type of flange face is used to make equipment and valves for all applications where Cast Iron is used for making. Cast Iron is brittle and is commonly used only in applications with low temperature, low pressure. The flat surface allows full contact of the two flanges across the entire face. Flat face flanges (FF) have a touch surface that is equivalent in height to the bolting thread of the flange. Full face gaskets are used between two flat side flanges, typically of the soft kind. According to ASME B31.3, as the resultant flanges joint will possibly leak, a flat face flange should never be matted with an elevated face flange.Raised Face Flanges (RF)The Raised Face Flange is the most common type used in process plant applications, and can be easily identified. It is referred to as a face raised because the surfaces of the gasket are positioned above the face of the bolting circle. Each style of mask requires a large range of gasket styles to be used, including varieties of flat ring sheets and metallic composites such as spiral-wrapped and double jacket forms.An RF flange aims to focus further pressure on a smaller area of the gasket and thus improve the joint’s pressure control capacity. Diameter and height, by pressure class and diameter, are described in ASME B16.5. Flange pressure level specifies the height of the face that is lifted. An RF flange aims to concentrate more pressure on a smaller area of the gasket, thereby increasing the joint’s pressure containment capacity. Diameter and height, by pressure class and diameter, are described in ASME B16.5. Pressure flange rating.
Is an ohmmeter connected in series or parallel?
You almost NEVER do. 1) The circuit should be off and/or disconnected when using an ohmmeter. 2) It should be in parallel with the component as far as the rest of the circuit is concerned, but alone in series with the device its measuring.
What is a machine that was never made?
We will never know because it has never been made yet!Another Answer:I think they meant machine ideas that were never invented, such as the Time Machine.
How are circuit breakers connected with the other elements in a circuit?
Both of these devices are safety devices used to open a faulted circuit and stop the current flow.
Advances in technology never depend on advances in science?
(true or false)advances in technology never depend on advances in science
What is a RFTBE weld neck flange I have never seen RFTBE related to flange description before?
Raised Face Through Bolt End.
Which will never get the vertical rays of sun?
srinagar
Why do we have vertical lines?
To create shapes. Think about it, without vertical lines there would never be tv....
How black holes make tornadoes on earth?
They don't. They never have. They never will.
What is 1 things that could never be placed in water?
Fire is 1 thing that could never be placed in water.
When will black holes die off?
never
Why there never can be a vertical line on a speed time graph?
Because - for there to be a vertical line - time would have to stand still !
Vertical angles are always sometimes or never complimentary?
Sometimes
Are vertical angles alway sometimes or never supplementary?
sometimes
Did you make black holes yet?
Black holes (in the astronomical sense) have never been made in the laboratory.
Do you trim new head gasket water jacket holes to fit your 95 Plymouth voyager 3.0?
No, you should never have to trim a head gasket. If the holes do not match up, you have the wrong gasket.No, you should never have to trim a head gasket. If the holes do not match up, you have the wrong gasket.
How powerful are black holes?
Black holes are so powerful, that if you were in one, it would stretch you apart and you would NEVER come out!!!
