answersLogoWhite

0

The function of any ballast in a lighting fixture is to raise the voltage high enough to strike an arc through the bulb or tube.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Engineering

Why halogen lamp is not required the choke and starter?

saanu ki pta


A choke coil placed in series with an electric lamp in an ac circuit causes the lamp to become dim why is it so?

The light is getting dim because the choke is using the energy the lamp should be using. The purpose of the choke is to remove transients; if it is using power at 50 or 60Hz, this is not desirable. My guess is this lamp is using a new energy efficient (not incandescent) light bulb? If this is the case, don't. If this is a choke you added to the lamp, then perhaps it's the wrong type choke (too large inductance). If you added this, it could be that you inadvertently inserted resistance in the lamp wire. Check to make sure nothing is getting hot around your new wiring. A bad solder point could cause this to some degree.


Why choke coil is used in tube light?

To limit the current through the lamp when the gas ionises and conducts.


What is the function of a capacitor in a fluorescent light fitting?

A capacitor is used to improve the power factor of the lamp.More detailsTo prevent the lamp from taking too much current a fluorescent lamp has to have a choke, which has magnetic inductance. The inductance has a negative impact on the power factor of the (the ratio between apparent power and real power taken by the lamp) - i.e. the power factor is reduced - so a capacitor is used to compensate for the inductance by improving the power factor so that it is closer to the ideal value of 1.Basically the inductor with the capacitor smooths out the voltage or current.


How does a choke work in a tube light circuit?

The choke works in conjunction with a starter . When you turn on the light , voltage is applied to the choke, and when the switch opens after a few seconds, it creates a high voltage across the contacts at each end of the tube. This starts the ionization of the gas , which glows. Once ionized, it continues producing light even when the voltage applied is only 120 VAC, the power line voltage.

Related Questions

What mean son in hpsv lamp?

The S in hpsv stands for sodium.


What is function of the choke in lamp circuit?

The function of a choke in a lamp circuit is to produce high voltage. In tubelights, the high voltage is essential for ionisation of the gas which is present in tubelights.


What is the function of igniter in hpsv lamp?

basically it generate high frequency.As you know when frequency increases voltage also increase.it produce frequency in kilo hertz.ULTIMATE function to produce high voltage,ie kilo volts.


What is hpsv lamp?

HPSV stands for High Pressure Sodium Vapor lamp. It is a type of high-intensity discharge (HID) lamp commonly used for outdoor lighting, street lighting, and agricultural applications due to its high energy efficiency and long lifespan. HPSV lamps produce a warm white or yellowish light and are known for their ability to provide good visibility and color rendering.


What is the function of a choke in a fluorescent lamp?

The inductance primarily serves to limit current flow to the correct level for the tube. It also can be used during startup to provide an inductive 'kick' forming a higher-voltage pulse to start the lamp.


Why halogen lamp is not required the choke and starter?

saanu ki pta


What is the input choke used for AC drive. What is its function?

The function of the input choke for an AC drive is much the same as the function of the choke on any other mechanical device. The jump start the unit the choke should be in the open mode. The stop the operation of the unit the choke should be moved to the closed position.


Functions of choke and starter in a fluorescent lamp?

The choke is used to limit the current flowing through the fluorescent lamp during start-up, allowing the lamp to warm up gradually. The starter is responsible for providing the initial high-voltage kick needed to start the lamp by ionizing the gas inside the tube. Together, the choke and starter work to regulate the flow of electricity and provide the necessary conditions for the fluorescent lamp to operate efficiently.


A choke coil placed in series with an electric lamp in an ac circuit causes the lamp to become dim why is it so?

The light is getting dim because the choke is using the energy the lamp should be using. The purpose of the choke is to remove transients; if it is using power at 50 or 60Hz, this is not desirable. My guess is this lamp is using a new energy efficient (not incandescent) light bulb? If this is the case, don't. If this is a choke you added to the lamp, then perhaps it's the wrong type choke (too large inductance). If you added this, it could be that you inadvertently inserted resistance in the lamp wire. Check to make sure nothing is getting hot around your new wiring. A bad solder point could cause this to some degree.


What is a peacocks job or function?

to choke


What is the function of rose?

what the function of lamp holder


How much power does a 250 watt hps light use an hour?

A 250 watt HPS light will use 250 watts of power per hour. This means it will consume 0.25 kilowatt-hours (kWh) of electricity in one hour of operation.