Actually a substation transformer for a distribution substation will reduce the incoming voltage from 115,000 volts or 69,000 volts to a lower voltage closer to 7200 volts that runs down the power poles in your neighborhood. At your house there will be a small transformer that reduces the voltage from 7200 volts to 240 volts to meet the needs in your home.
Actually both are wrong !!
switching station is intermediate station between two other substations or between substation at load end and generating station. at switching station incoming power line and out going powerlines have same level of voltage it means there is no transformer to step down the voltage to connect the load. switching stations are created just for purpose of controlling important parameters in power system and control of voltage rise due to capacitive effect or voltage drop due to reactive effect or both .
The substation is the point in the T&D system at which the generated voltage is either stepped up for transmission or stepped down for distribution. This is accomplished by a large power transformer within the substation. The lower distributrion voltage is carried from the substation on feeder circuits that eventually make their way to the smaller pole-mounted or pad-mounted Transformers that we see in our neighborhoods. These transformers further step down the distribution voltage (normally 12kv) to the useable 240/120 volts that we use in our homes.
In my industry (Electrical Power Generation) this is known as a electrical circuit protection (device)circuit breaker, but it is not located at the Power Station but remotely in another location maybe inside a sub station building maybe its outside in the sub-station switch yard. These circuit breakers are automatic in operation (tripping open for circuit protection)) but maybe closed (if electrically safe to do so) remotely at a control centre/control room, some actually will automatically try to close a number of times and if the fault is cleared they will stay closed if the fault still exists they will then remain open and have to be reset once the fault is rectified. Hope this helps.
A transformer is an electrical machine which either steps up, or steps down, voltage. A substation is a location where transformation and/or switching takes place.
In its simplest form, a substation can be a pole- or pad-mounted transformer, together with its protective equipment (hv and lv fuses). In its most complex form, a substation can be a large fenced yard, containing several transformers, switchgear, busbar systems, and a building housing switchgear, busbar systems, and complex protective systems.
Substations do not normally contain generating plant (other, perhaps, than a standby generator).
Power transformers are used in electricity transmission systems to either step up, or to step down, system voltages. They step up the voltage produced by the alternators in the power station to the very high levels necessary for transmission, then gradually step down the transmission voltages at substations located in and around load areas (e.g. near cities, etc.).
Current transformer and voltage transformer . This transformers are actually measuring instruments which measures the quantity of current and voltage coming out of the substation.
A arrangement of Equipment between two bus-bars. Example 1 and 1/3, 1 and half etc.
Primary substation - when the transformer is HV/MV or MV/MV. e.g. substation designed for 132kV/33kV or 230kV/22kV or 33kV/11kV etc stepped down for MV distribution (mainly for utilities and heacy industries) Secondary substation - when the transformer is HV/LV or MV/LV. e.g. substation designed for 11kV/400V or 6.6kV/400V etc stepped down for LV distribution (mainly for residential, commercial) sometime referred to as a kiosk substation.
An isolation transformer is usually a ferromagnetic transformer. The question needs to be framed more usefully.
The difference between current transformer and potential transformer is that the secondary of a current transformer can not be open circuited while under service whereas that of the potential transformer an be open circuited without any damage to the transformer.
three phases
Ground clearance in a substation is the distance between wires and the ground or other objects such as buildings. Sectional clearance is the distance between the wires themselves in a substation.
Current transformer and voltage transformer . This transformers are actually measuring instruments which measures the quantity of current and voltage coming out of the substation.
use of CT
A arrangement of Equipment between two bus-bars. Example 1 and 1/3, 1 and half etc.
Prefabricated power distribution substation Its basically a whole 11kv substation but in one unit. It contains a transformer, ring main unit, fuse board and circuit breakers etc. It still uses as much space as a normal substation that houses a separate transformer, ring main unit etc but is easier to transport and is probably cheaper.
Primary substation - when the transformer is HV/MV or MV/MV. e.g. substation designed for 132kV/33kV or 230kV/22kV or 33kV/11kV etc stepped down for MV distribution (mainly for utilities and heacy industries) Secondary substation - when the transformer is HV/LV or MV/LV. e.g. substation designed for 11kV/400V or 6.6kV/400V etc stepped down for LV distribution (mainly for residential, commercial) sometime referred to as a kiosk substation.
there is nothing like a balanced and unbalanced transformer.
the pocket substation have three major parts and they are transformer , ring main unit (RMU) and low voltage distribution bored (LVDB).
Both are same. This is an instrument transformer used for metering & protections.
The 3 kVA transformer will weigh double the 1.5 kVA transformer.
basically there will not be any difference between them. the capacity of equipment will be more such as the CB rating will be more basically there will not be any difference between them. the capacity of equipment will be more such as the CB rating will be more