0
This (C-60 or C-90) is a temperature ratting of wire. It is the ambient (area) temperature, in degrees celsius, that a wire can be used without de-ratting or adverse resistance characteristics becoming a problem. If I had a home in Nome, Alaska, I would have no problem wiring the attic with C-60 wire. However, I would use C-90 if the same home where in Phoenix, Arizona. Hope this helps! Terry SAFETY FIRST and ALWAYS!
Add your answer:
Earn +20 pts
Wiring diagram of a direct online motor-electrical engineering?
No idea what a direct online motor is but it certainly sounds like a peice of electrical engineering - especially if there is a wiring diagram of it.
Can wiring and plumbing be located in the same chase?
No most certainly not, firstly, if laying copper water pipes and then you lay wiring next to it, it doesnt matter how much of insulation there is it will cause electrolosis. And weaken the pipe causing it to burst therefore affecting the electrical wiring and water and electricity do not go well together. Secondly chasing galvanised pipe into a wall is definitely not recommended because when the galvanised pipe "sweats" it will start to rust as the moisture just sits in the wall also causing the pipe to burst and affecting the electrical wiring. There must be a minimum 200mm between the chasing for electrical wiring and plumbing pipes.
Diff between electrical and electronics?
One definitionOne view point is that "Electrical" relates to the development and delivery of the electrical energy to the various devices that perform specific functions in a given environment. Example: The alternator in your car that series of wires delivers electrical power / energy to various components (radio, the computer that monitors / controls operation of the engine) in to-days cars. Where as "Electronics" relates more to the complex functions performed within a given device, more often now days by circuits comprised of many micro electronic sub components that make up the structure of a single micro electronic component. Example: a typical CPU chip would / could contain thousands of individual transistor circuits within a device no bigger that the size of your small finger nail with room to spare.In short: electrical circuits handle transfer of energy - electronic circuits handle transfer of informationwhat is the main difference between electrical and electronics ?In short: electrical circuits handle transfer of energy - electronic circuits handle transfer of informationRead more: http://wiki.answers.com/What_is_the_difference_between_the_terms_Electrical_and_Electronics#ixzz1RmeXS2Zv
What is flex outlet?
An appliance cable or "flex" outlet is a type of electrical outlet which is NOT a "socket outlet" to take plugs for appliances so that they can be plugged and un-plugged. An appliance cable or "flex" outlet has terminals inside it. The terminals allow the wires in an appliance cable or "flex" to be connected to the household wiring in a building. The household wiring comes from the building's main electrical power panel, which carries the main circuit breakers. The circuit breakers are fitted to protect the household wiring from catching on fire if any circuit is overloaded. Such appliance cable or "flex" outlets also have strain-relief clips. A strain-relief clip helps to prevent the cable from being yanked out of the outlet if the appliance gets moved away from the wall where the outlet is installed. Such outlets, with terminals inside and strain-relief clips, are used for fixed appliances, such as ranges or dryers, which should never have to be un-plugged during normal use of the appliance by the user.
How do you Describe the problems that can occur with the wiring and testing operations?
Testing and wiring should be carried out by a qualified , trained technician / engineer so that the electrical devices and wiring are properly done with safety.
Can an astable multivibrator replace household wiring if the circuit is modified?
No. Household wiring requires household wiring.
Why is the best conductor not used for household wiring?
Copper is an excellent conductor of electricity, but it is more expensive than aluminum. Aluminum is commonly used for household wiring as it is cheaper, lighter, and still has good conductivity. Additionally, aluminum wiring is safe when installed properly and can meet electrical codes and standards.
Where do you find fuse?
It depends on where it is installed. Household fuses are always in the fuse box. When power goes out in your house, you check the fuse box first.
What is a Black wire in a household circuit?
A black wire in a household circuit is typically the hot wire that carries electrical current from the electrical panel to the device or outlet being powered. It is an important part of the circuit that must be connected properly for the electricity to flow correctly and power the intended device.
Which is the positive wire between a white and black wire?
That depends if it is automotive or household wiring. On a car a black wire is almost always ground. On house wiring black is the supply (hot) wire.That depends if it is automotive or household wiring. On a car a black wire is almost always ground. On house wiring black is the supply (hot) wire.
What is electrical wiring connection in domestic house in India?
domestic electrical wiring designig
What is the difference between 12 2 and 14 2 wiring?
2.4
Why we measure voltage between neutral to earth?
To ensure that it complies with the relevant electrical wiring regulations.
What is difference between cleat and conduit wiring?
Cleat wiring is exposed while in conduit wiring the wires are well protected inside tubes/pipes.
What is the difference between conduit and pipe?
Tube and pipe are both used for conveying liquids or gases under pressure. They differ in how they are sized and their rigidity. A conduit is mainly used to protect and route electrical wiring.
What has the author James L Kittle written?
James L. Kittle has written: 'Home heating and air conditioning systems' -- subject(s): Air conditioning, Amateurs' manuals, Dwellings, Heating and ventilation 'Home electrical repair and maintenance' -- subject(s): Amateurs' manuals, Interior Electric wiring 'Mastering household electrical wiring' -- subject(s): Interior Electric wiring
How is godown wiring different from hostel wiring?
Godown wiring refers to the electrical wiring system in a storage facility typically designed for efficient lighting and power supply to large spaces. Hostel wiring refers to the electrical wiring system in a residential building that accommodates multiple occupants, with individual rooms or living units having their own wiring for lighting, power outlets, and other electrical needs. The main difference lies in the scale and complexity of the wiring design to suit the specific usage requirements of each type of building.
