answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: What is alternate and chop mode in dual trace oscilloscope?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

Dual trace oscilloscope along with block diagram?

in the dual trace cro the same electron beam is used to generate the two traces that can be deflected from two independent vertical sourceThe signal trace capability of the conventional CRT can be modified to produce dual image or dual trace display, by means of fast electronic switching of two separate input signals. Channel A and Channel B with preamplifier and delay lines feed their input to an electronic switch that alternately connects the input of the main vertical amplifier to the two signal inputs. The same are displayed with various display modes.When the display mode selector is in the alternate position, the electronic switch alternately connects vertical amplifier to channel A & B. The switching rate is synchronized to the sweep rate, so that CRT spot traces channel A signal on one sweep and channel B on next. Since these signals have calibrated input attenuator and a vertical position control, the amplitudes of the input signal can be adjusted individually and the two images placed separately on the screen. This mode is useful with fast sweep rates, when the two images appear as one simultaneous and state display.In chopped mode electronic switch is free running at the rate of 100 to 500 kHz, entirely independent of the frequency of the sweep generator. In this, switch successively connects small segments of A and B waveforms to the main amplifier. At fast chopping rate of 500 kHz, or say 1 microsecond, sweep of each waveform is fed to CRT for display. If the chopping rate is much faster than the sweep rate, the individual segments reconstitute the original A and B waveforms on screen without interruptions in the two images. If sweep rate approaches the chopping rate, the segments' waveforms become visible as individual images and the continuity of image display is lost, which is less picturesque than the alternate mode of position.The use of polarity inversion switches can display A+B, A-B, B-A, and -A-B modes.In the X-Y mode the sweep generator disconnects channel B and is connected to the horizontal amplifier. This gives good X-Y measurements with same amplifications. In addition the dual trace CRO can be used as single beam CRO, displaying either A or B as a function of time.


Is an Intel Celeron processor a dual core processor?

There are Celeron dual core processors today. However, just because you have Celeron processor, it does not mean your Celeron processor is a dual core processor. The easiest way to tell is to look at the Intel sticker on your computer. If it says "Dual Core," then it is dual core. If it does NOT say "Dual Core," then it is not dual core.


Which is better dual core or i3?

difference between dual core and core i3


Compare multi-core and dual core?

"Dual core" implies that there are two separate instruction execution units placed on a single "die." Some use shared components, such as cache, while others have two full processors, including all sub-components. All dual core processors could be considered multi-core (which simply means multiple "cores" or "processors"). However, a tri-core or quad-core is also a multi-core. Therefore, all dual cores are multi-cores, but not all multi-cores are dual cores.


What is full Form of DIN?

the fullform of DIN is Dual In Process

Related questions

What are the advantages of dual trace over dual beam CRO for multiple trace?

what are the advantages of dual trace oscilloscope


What is the difference between dual trace cro and dual beam cro?

In a dual beam oscilloscope we are using two separate electron beam for producing different wave forms. But in a dual trace oscilloscope the same beam is used for producing two different wave forms


Working principle of dual trace oscilloscope?

Dual-trace operation allows you to view two independent signal sources as a dual display on a single CRT. This operation allows an accurate means of making amplitude, phase, time displacement, or frequency comparisons and measurements between two signals. A dual-trace oscilloscope should not be confused with a dual-beam oscilloscope. Dual-beam oscilloscopes produce two separate electron beams on a single scope, which can be individually or jointly controlled. Dual-trace refers to a single beam in a CRT that is shared by two channels.


Price of dual trace oscilloscope tektronix 465b?

About $100-$300 depending on condition!


What is Difference between dual trace oscillosope and dual trace generator?

Oscilloscope is used to display electrical signals on a display. A dual trace oscilloscope can display two signals simultaneously. For a trace generator I think you mean a signal or a function generator which generates electrical waveforms of varying shapes, frequency and amplitude. A dual trace or a function generator in that sense is an equipment capable of generating two independent waveforms at the same time. - Neeraj


Will a dual trace oscilloscope have one set of position control?

Nope - it has controls for each trace. I have a DTO and it has controls to position the trace horizontally for each channel.


What is the difference between dual trace oscilloscope and dual beam oscilloscope?

hello! dual beam oscilloscope has 2 filament in crt tube that made 2 independ beam. but tahe dual trace oscope has 1 beam and made 2 channel indicate on screen by high frquency switcher. it mean,one beam alterative swtch between ch1 and ch2 to indicate 2 channel waveform. excuse me for bad english knowledge!! bye


What do you mean dual beam cro?

A dual beam oscilloscope, also known as a dual beam CRT (cathode ray tube), is a type of oscilloscope that utilizes two electron beams for displaying multiple signals simultaneously on the screen. This allows for easy comparison and analysis of two separate waveforms.


What do you mean by dual channel of cathode ray oscilloscope?

An oscilloscope with 2 vertical inputs that are multiplexed to the CRT, either by chopping them together on every sweep or alternating between them on every other sweep. Some oscilloscopes also support a differential mode where the 2 inputs are subtracted to produce a single combined signal.


Dual trace oscilloscope along with block diagram?

in the dual trace cro the same electron beam is used to generate the two traces that can be deflected from two independent vertical sourceThe signal trace capability of the conventional CRT can be modified to produce dual image or dual trace display, by means of fast electronic switching of two separate input signals. Channel A and Channel B with preamplifier and delay lines feed their input to an electronic switch that alternately connects the input of the main vertical amplifier to the two signal inputs. The same are displayed with various display modes.When the display mode selector is in the alternate position, the electronic switch alternately connects vertical amplifier to channel A & B. The switching rate is synchronized to the sweep rate, so that CRT spot traces channel A signal on one sweep and channel B on next. Since these signals have calibrated input attenuator and a vertical position control, the amplitudes of the input signal can be adjusted individually and the two images placed separately on the screen. This mode is useful with fast sweep rates, when the two images appear as one simultaneous and state display.In chopped mode electronic switch is free running at the rate of 100 to 500 kHz, entirely independent of the frequency of the sweep generator. In this, switch successively connects small segments of A and B waveforms to the main amplifier. At fast chopping rate of 500 kHz, or say 1 microsecond, sweep of each waveform is fed to CRT for display. If the chopping rate is much faster than the sweep rate, the individual segments reconstitute the original A and B waveforms on screen without interruptions in the two images. If sweep rate approaches the chopping rate, the segments' waveforms become visible as individual images and the continuity of image display is lost, which is less picturesque than the alternate mode of position.The use of polarity inversion switches can display A+B, A-B, B-A, and -A-B modes.In the X-Y mode the sweep generator disconnects channel B and is connected to the horizontal amplifier. This gives good X-Y measurements with same amplifications. In addition the dual trace CRO can be used as single beam CRO, displaying either A or B as a function of time.


What is the dual aspect concept?

Dual Aspect concept: This state that there are two aspects of accounting, one represented by the assets of the business and the other by the claims against them. The concept states that these two aspect are always equal to each other. In other words, this is the alternate form of the accounting equation: Assets=Liabilities+Capital Dual aspect concept is known as "Double Entry Book Keeping System".


What is dual relationship in counseling practice?

A dual relationship in counseling is when the counselor/therapist has more than one social role related to the potential client. For example, you would not be someone's "neighbor" or "cousin" and also their "therapist." If there is question as to whether you may be in a dual relationship situation, it is best to ask (if you are the potential client) or provide (if you are the potential therapist) information for alternate providers to avoid any conflict of interest.