Wiki User
∙ 13y agoAs you add more bulbs to a series circuit that means that the bulbs are in series to one another, therefore the total resistance is the sum of the individual resistance of the bulbs. If you add bulbs of the same resistance,then the rate at which the resistance changes will increase in a constant manner provided the current source is not altered. For instance if the bulb you are using is rated 20v,60w, then the current passing via the bulbs in series is the square of the voltage divided by the power in this case the current is approximately 7amperes.
Wiki User
∙ 14y agoWiki User
∙ 12y agoWhen a resistor is added to a series circuit, the voltage across each of the original
elements in the circuit decreases, the current in the circuit decreases, and the total
power dissipated by the circuit also decreases.
Wiki User
∙ 10y agoA resistor slows the flow of electricity, and converts the electrical energy into heat. You don't WANT heat - you want LIGHT, so we generally do not put resistors in lighting circuits. If there is a resistor in the circuit, it will cause some of the energy that would normally be converted to light to be converted into heat instead, so the light bulb will glow less brightly.
A variable resistor in such a circuit is sometimes called a "dimmer".
Wiki User
∙ 13y agoThe current will decrease and the light will dim.
Wiki User
∙ 9y agoResistance increases
the light bulb gives off more light
All of the light bulbs in the series circuit would go out.
In a series circuit each light completes its part of the circuit and connects to the next light. So, if one light fails, the circuit is broken and the flow of current to all lights must stop.
If one light bulb in a series circuit fails, all the other light bulbs will go out, until the failed bulb is replaced and the series circuit is completed again.If one light bulb in a parallel circuit fails, all the other light bulbs will still work.
Toasters and lightbulbs.AnswerA resistor is an circuit component. So, while toasters and light bulbs have resistance, they are not resistors!
The total current in the circuit will decrease.
The circuit current is interrupted and all the lights will go out.
A resistor slows the flow of electricity, and converts the electrical energy into heat. You don't WANT heat - you want LIGHT, so we generally do not put resistors in lighting circuits. If there is a resistor in the circuit, it will cause some of the energy that would normally be converted to light to be converted into heat instead, so the light bulb will glow less brightly. A variable resistor in such a circuit is sometimes called a "dimmer".
Independent variable: the number of cells in the circuit. Dependent variable: the current measured by the ammeter. Control variable: resistance of the resistor, type of light bulb.
the light bulb gives off more light
In a series circuit, when a light bulb is broken, it creates an open circuit which stops the flow of current throughout the circuit. As a result, all the other light bulbs in the circuit will also stop working because they are all connected in a series.
A variable resistor can be connected in series with a light bulb in a circuit. By adjusting the resistance of the variable resistor, the current flowing through the circuit changes, affecting the brightness of the light bulb. Increasing the resistance decreases the current, resulting in lower brightness, while decreasing the resistance increases the current, leading to higher brightness.
in a series circuit current flows through each resistor or light bulb and if one item burns out the complete circuit goes dead such were the old fashioned xmas tree lights. They were wire in series and if one light burned out you had to test each light bulb til you found the one burned out to get the whole string to work again. In a parallel circuit each resistor, motor, light bulb has its own ground so if you lost one light in a circuit the rest of them continue to burn.
If you unscrew a light bulb in a series circuit, it will cause an open circuit, which will break the flow of current in the circuit. As a result, all other bulbs in the series circuit will also turn off because there is no longer a complete path for the electricity to flow.
In a series circuit, all bulbs are necessary to complete the circuit. If one bulb goes out, the circuit is broken, so none of the bulbs would light up.
All of the light bulbs in the series circuit would go out.
Resistance is increased so the light will be dimmer.