0
Add your answer:
Earn +20 pts
What is the primary tool you use to interact with a graphical user interface?
A mouse because you use it to control a cursor on your screen, the cursor is part of the graphical user interface
What is vf speed control?
It is used for sensorless motor control. With vf speed control u can control speed of any induction motor.
Is cursor implementation possible in queue or stack?
yes,cursor implementation possible in priority queue.
why we use variable speed drivers in motor control units?
Variable speed drivers are necessary to be able to have different speed settings in a motor.
What do courteous operators always do?
control speed,noise, and wake
What is the function of the cursor?
the function of cursor control keys it helps to move the cursor.
What is the function of the cursor key?
the function of cursor control keys it helps to move the cursor.
How do you change a mouse cursor?
In control pannel, select the cursor option..... and then, select ur cursor type.
How can you edit a cursor into your computer?
Start, control panel, mopuse and from there :)
Where is the Idle speed control valve on a 1999 Mercedes?
Does not have one. Idle speed is controlled electronically through an idle speed control module.
How to adjust computer mouse to work in a smaller range area?
You can increase the pointer speed, so that the cursor moves a greater distance even though you only physically move the mouse a tiny distance. To change the rate for the cursor...Click... Start > Control Panel > Mouse > Pointer options. Move the slider to where you're comfortable with the pointer speed, and click Apply, then OK
How do joysticks work?
The working of a Joystick is totally based on the potentiometers attached to it. The movement of stick in any direction from center position corresponds to the movement of cursor on screen in the same direction. The amount of movement is measured by the potentiometers and the springs return the stick to the position. A small movement of stick moves a lot , the cursor on the screen because the movement of it is amplified approximately 5 to 10 times in the movement of the cursor. The Joystick is mostly used to control the velocity of the cursor movement in various games. Like in car race it is used to control speed of car but is not used to control or locate the absolute position of the cursor. The basic reason behind it is the amplification of stick movement for moving the cursor. Because of this amplification the movement of cursor is also jerky and may not be positioned quickly and accurately. This is why the joysticks are more used for games and are less used for graphics. A joystick is a low speed device and is perfectly suited for use with USB port. A USB Joystick requires special drivers because the original joysticks are analog devices that need to have special drivers to interrupt the digital signals as equivalents to the original design which used analog levels.
Your cursor bar is too wide Help?
Go to: Start> Control Panel> Accessibility Options> Display Tab> Cursor Options: Then reduce the Cursor "Width" to a Narrower setting. Hope this helps. HSter2 Note: This applies if your Operating System is Windows XP.
Where can I get your pencil mouse cursor?
it should be on the computer, go to control panel, then mouse then settings and change it.
Why is there red and black sides on a table tenis bat?
One for control one for speed
What does a speed sensor control?
A Vehicle Speed Sensor (VSS) senses the speed of the vehicle. Used for automatic transmission shift points and other electronics. Another speed sensor would be a wheel speed sensor. This one monitors wheel speed for ABS and Traction control.
How do you get the two clocks to strike 12 in the haunted house on Poptropica?
A skull pops up when a clock strikes midnight (both hands point up). The object is to have both skulls pop up at the same time, but the clocks show different times. By placing your mouse cursor over one of the clocks, you cause it to speed up. When you move the cursor away, it goes back to its regular speed after a few seconds. By speeding up one, or both, of the clocks, you can get them to keep about the same time. You can get it fairly close, then at the last second before 12, speed the slower one up so that both skulls come out at practically the same time. This may take a little practice. Be sure to keep the cursor away from both clocks until you want one to speed up. A lantern will appear in the fireplace. There is kerosene fuel for it under the stairs in the basement.
