0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Is 250 considered a deep well or shallow well?
Anything over 80 feet is considered a deep well. A jet pump can pump up from 80 feet, more than that needs a submersible pump.
Can you replace a two pipe jet pump with a single pipe jet pump?
Yes you can if the water level from the inlet of the pump is less than 25 feet. That's the limit of a shallow well jet pump. It can lift water physically 25 feet vertically, no more. If the well casing diameter is three inch or larger you could also install a submersible pump.[url="http://www.pumpsandtanks.com/Pumps/jet_pumps.htm"]Jet Pumps[/url]
Calculate pump efficiency for submersible pump?
pump eff. = (pump dynamic head x pump flow)/(pump h.p x 3960)flow=gallon per minute
Why is there no water coming from the well?
Assuming that the pump and the pipes are O.K.then your water level has probably dropped.ANS 2 - It is possible, but unlikely for the well level to drop unless many new people or businesses are sucking from the aquifer you are on. Many things can go wrong with pumps and well pressure tanks. If you have a jet pump (motor and pump on surface) these are very susceptible to air leaks in the pipes to well. Check this. If you have a submersible pump the control box can develop problems. -If you have an old pressure tank it can get 'waterlogged'. If you are unfamiliar with any of this hire a well technician or a local well company to check it out.
How much does it cost to replace well pump?
There are many variables here, so I will answer as best as I can. The pump cost itself depends on whether it's a Shallow Well jet pump, a Deep jet pump or a Deep Well submersible. A shallow jet pump can be found as low as 350 for a reasonable 1/2 hp model that will suck from about 24 feet max. -A deep well jet can suck from 80 feet, and these are seldom less than 550 or so to buy.An average 3/4 hp submersible (which I believe to better in every case, even in shallow wells) will cost you around 750-800 for a good new one. These will pump (rather than suck) from anywhere down to 5-600 feet. I always prefer to use these type of pumps as they are far more reliable, easy to fit and long lasting. -More money to begin with, but a much better deal ! -Other necessities are the drop tube and wire, For tubing I always use 1" polypropylene thick wall tube - about 70 cents per foot. For a submersible also add 14/4 wire which runs about a dollar per foot (all the way down to the pump.) -Wire for a jet pump is negligible as the pump is on the surface.It takes about 5-6 hours labour to fit a deep well sub pump and about 4-5 to fit a jet pump. I don't know where you are, so can't price labour. Here in western Canada it runs 85-105 per hour.Some other tips- Definitely NOT a good idea to use old tubing for the pumpdrop. - If it's a deep well Submersible always change the control box.- If its a jet pump of any type, heat all tubing before connecting and doing up clamps. Most problems with jetpumps start with small air leaks at badly connected tubing. - Alwaysmount a shut off ball valve between jet pump and pressure tank. -You'll see why when you prime it !- Before starting either pump first time, make sure your pressure tank has an adequate air charge !
How can I stop a submersible well pump that is constantly running?
You can buy a timed switch mounted on the submersible pump. If you want to buy a submersible pump, you can choose VIDO's submersible pump, VIDO's submersible pump is of high quality and is the choice of most people.
What is a submersible well pump used for?
A submersible well pump is a pump that is used for pumping water from wells. There are websites that offer submersible well pumps for sale if you need one.
What stands for 150mm submersible pump?
150mm means the well diameter is 150mm, and the well of submersible pump is divided into several specifications. If you want to buy a submersible pump go to VIDO, VIDO's submersible pumps are of high quality and are the choice of most people.
How can you remove submersible pump which was struck in bore-well under 200 feet?
how lift submersible pump stuck 300ft
How do I install a submersible pump and what if something goes wrong?
Submersible pumps are best installed by the professionals. These items are hardwired and can be quite dangerous so installation of these items are not recommended for the "do it yourselfer".
How do you compute for the power of a submersible pump?
To compute the power of a submersible pump, you need the pressure and the pump power.
How much would one expect to pay for a top of the range submersible pump?
Submersible pumps can be purchased at stores such as Home Depot, Canadian Tire as well as Lowe's. A top of the line submersible pump can cost approximately $400 at Home Depot.
How does a submersible pump work in a water well?
A submersible pump is normally fitted with a float switch. As the water rises, the float switch turns the pump on. When the pump empties the water from the level and the level falls again, the float switch turns the pump off again.
Why won't my submersible well pump not turn on?
probably the wire connections are not connected properly
How much does it cost to operate a submersible pump?
The cost to operate a submersible pump depends on how big the pump is and how long its average duty cycle is.
How does a submersible water pump work in a well?
A submersible pump is normally fitted with a float switch. As the water rises, the float switch turns the pump on. When the pump empties the water from the level and the level falls again, the float switch turns the pump off again.
Submersable well pump pumps air and water?
No, pumps water only. A submersible pump can only pump what it is submerged in and since there is no air under water......
