0
What else can I help you with?
How can you hook a 230v 3 phase lathe to 480v 3 phase incoming power?
Inspect all motor labels and see if they are dual voltage motors. If they are, they should have a label on them telling you how to convert the motors for 480 volt. This is a relative simple task. Converting to 480 volts will lower the motor current to half of the 230 volt rating, so you will have to change the overload heaters in the individual motor starters. You need to do this to protect the motors in case of overloading. Last the control transformer will need to be reconnected for 480 volt.
What does the phases on a nameplate of a motor mean?
On a three phase motor, the phases give you direction for how to hook the motor up to make it spin one direction vs. the other. If you hook up such a motor blindly with all three phases, it may spin in the opposite direction you want; to fix, you swap any two of the three phase connections.
How do you hook up a 3 phase water heater to a 3 wires 1 white 1 black 1 bare copper ground?
In order to answer your question, firstly, we have to accurately establish your supply.Is it 2 phase or 2 wire?2 phase is two active conductors, i.e. 2 live wires with reference to neutral or ground2 wire is single phase, an active and a neutral conductor.2 phase supply is uncommon.Single phase (2 wire) is the more common supply and for installations with large loads three phase, or, more appropriately 3 phase and neutral (4 wire) is used.Please confirm your supply so that a detailed answer can be provided.
How do you hook up 9 lead 3 phase motor?
Don't know of any three phase low voltage motors. Perhaps it's a "stepper motor". Stepper motors are typically computer controlled, with the computer pulsing different pairs of wire to cause the motor to "step".
Can you hook up only 2 of the 3 phase lines to a breaker switch to use as a on off switch for 3 phase paint booth motor?
In single phase applications, you have two wires. One of these is "hot", meaning it has an AC voltage applied to it. The other is not - it is directly tied to ground or the system neutral. In three phase power, all three wires are "hot", and use the other wires as the return path under balanced conditions. Because of this you cannot do what you are proposing and have a safe setup. Isolating only two of the three wires still leaves one "hot".
How can you hook a 230v 3 phase lathe to 480v 3 phase incoming power?
Inspect all motor labels and see if they are dual voltage motors. If they are, they should have a label on them telling you how to convert the motors for 480 volt. This is a relative simple task. Converting to 480 volts will lower the motor current to half of the 230 volt rating, so you will have to change the overload heaters in the individual motor starters. You need to do this to protect the motors in case of overloading. Last the control transformer will need to be reconnected for 480 volt.
How do you hook 230v air compressor to house?
You would have to install a 230 volt outlet.
Can you hook up a stove to a normal three phase socket?
If this is in your residence it is extremely unlikely you have 3-phase power. You need an electrician to make sure you don't burn down your house.
What does the phases on a nameplate of a motor mean?
On a three phase motor, the phases give you direction for how to hook the motor up to make it spin one direction vs. the other. If you hook up such a motor blindly with all three phases, it may spin in the opposite direction you want; to fix, you swap any two of the three phase connections.
How do you hook up a three phase welder?
Easy as one,two and three. There are four primary wires coming from you service panel.(provided you have three phase service) you can check by looking at the weather head on the roof. if it has three wires you have single phase but if it has four then you have three phase. the hot wires will be black,red and brown. the neutral will be white or green. the welder should have a manual that will give you the lead phase wire(most likely black to black) the other two hot wires can hook to any other hot wire. The neutral goes to the white or green and posts to the panel. If the welder has a switching power supply then you must have a three phase converter.
How do you hook up 3 phase to a 10 hp compressor?
To hook up a 10 hp compressor to a 3-phase power supply, connect the three hot wires from the power supply to the terminals L1, L2, and L3 on the compressor's motor starter. Connect the neutral wire (if required) to the N terminal. Lastly, connect the ground wire to the ground terminal. It's advisable to consult a professional electrician or the compressor's manual for specific instructions.
How do you hook up a 3 phase water heater to a 3 wires 1 white 1 black 1 bare copper ground?
In order to answer your question, firstly, we have to accurately establish your supply.Is it 2 phase or 2 wire?2 phase is two active conductors, i.e. 2 live wires with reference to neutral or ground2 wire is single phase, an active and a neutral conductor.2 phase supply is uncommon.Single phase (2 wire) is the more common supply and for installations with large loads three phase, or, more appropriately 3 phase and neutral (4 wire) is used.Please confirm your supply so that a detailed answer can be provided.
How do you hook up 9 lead 3 phase motor?
Don't know of any three phase low voltage motors. Perhaps it's a "stepper motor". Stepper motors are typically computer controlled, with the computer pulsing different pairs of wire to cause the motor to "step".
Where can you get a free wiring diagram for a 480 volt reversible motor?
You can try contacting the manufacturer of the motor or searching for the wiring diagram on their website. Another option is to check online databases or forums dedicated to electrical topics, where professionals may share wiring diagrams for various motors.
what part of speech is hooked?
Hook is a verb (to hook) and a noun (a hook).
What is the hawaiian word for hook?
The Hawaiian word for hook is "makau." It is commonly used in fishing and means hook or fish hook.
What does P1 stand for in electrical wiring?
P1 is where you hook L1 on electric motors. Typically used on 220v motors in the wiring diagram. P1 (phase 1) gets connected to L1 (power leg)
