answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: How do you connect two motors to a single vfd?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

Can you connect a 3 phase motor to a 1 phase supply?

Single phase to three phaseThe physical internal windings between single phase and three phase motors makes this an impossibility That being said money can make anything happen. Depending on the amount of money you want to spend to make this happen there is a device on the market called a VFD ( Variable Frequency Drive). On the three phase input terminals you apply your single phase voltage. On the output terminals you connect your three phase motor. When run in this configuration there is an internal switch that has to be changed to let the VFD know that it should be looking for only two lines on the input to be hot. Other wise the VFD thinks that there is a line loss on the three phase input terminals and the unit will not start.Some 3 phase motor speed controllers can be run off a single phase supply, this caused us a problem at work when a new speed control was fitted to some laundry equipment, as we then had to rewire the supply to bring in a nuetral, so i suggest a speed controller is probably the solution.


How you can connect three single phase transformers as a three phase transformer Y to Y?

You can not unless the installation is a motor and cost is not important. Depending on the amount of money you want to spend to make this happen there is a device on the market called a VFD ( Variable Frequency Drive). On the three phase input terminals you apply your single phase voltage. On the output terminals you connect your three phase motor. When run in this configuration there is an internal switch that has to be changed to let the VFD know that it should be looking for only two lines on the input to be hot. Other wise the VFD thinks that there is a line loss on the three phase input terminals and the unit will not start.


How can you run a three phase motor on a single phase supply?

for countries in Europe and other world areas running a 50 Hz supply service. UK household AC power mains voltage is now 230V (previously it was 240V) 50 Hz. From a 415 volt 3-phase incoming supply you will get this voltage between any ONE line and the Neutral.Between any two lines you will get 415V. DO NOT WIRE IT LIKE THIS!So, if you wire the motor to any ONE line (and ONLY ONE) and Neutral you'll get the correct voltage.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.+++My advice would be to buy a proper transformer which can be connected to a 415V 3ph input and give 230V 1ph output at a current rating suitable for the motor and its purpose. I assume the questioner's installation is in a commercial premises because domestic supplies in the UK are 230V 1ph only - running a 3ph motor off that requires a suitable inverter.


How do you operate a vfd?

VFD is an adjustable speed drive that is used mostly in electro mechanical drive systems that control AC motor speed. VFD has come down on cost and the size which improved performance through advance in switching devices.


What is vfd called as variable frequncy drive?

VDF is variable frequency drive.In AC (alternative current) induction motors the speed is obtained by parameters like poles and frequencyformula Ns = 120 x f/ pwhere N= (synchronous ) speed rpm of motor. F = frequncy Hz of the power supply ex:50Hz, 60 Hzto obtain variable speed of the motor by changing the frequncy it is achived with the help of VFD device.

Related questions

What is a VFD and can it be connected in single phase to obtain three phase power?

Depending on the amount of money you want to spend to make this happen there is a device on the market called a VFD ( Variable Frequency Drive). On the three phase input terminals you apply your single phase voltage. On the output terminals you connect your three phase load. When run in this configuration there is an internal switch that has to be changed to let the VFD know that it should be looking for only two lines on the input to be hot. Other wise the VFD thinks that there is a line loss on the three phase input


Will a 400V 3 phase machine work on a single phase supply?

The physical internal windings between single phase and three phase motors makes this an impossibility That being said money can make anything happen. Depending on the amount of money you want to spend to make this happen there is a device on the market called a VFD ( Variable Frequency Drive). On the three phase input terminals you apply your single phase voltage. On the output terminals you connect your three phase motor. When run in this configuration there is an internal switch that has to be changed to let the VFD know that it should be looking for only two lines on the input to be hot. Other wise the VFD thinks that there is a line loss on the three phase input terminals and the unit will not start.


What are the Applications of induction motors?

Introductionl It is becoming very popular the utilization of squirrel cageinduction motors with variable frequency drives (VFD's) in theindustry.l The advance of power electronics technology and the cost of theVFD's are making this utilization possible.l The many advantages of this type of application are:ÙSpeed variation.ÙHeavy load inertia starting.ÙHigh starting torque requirements.ÙLow starting current requirements.ÙHigh efficiency at low speed.ÙHigh power factor.l The induction motor with VFD's replaces with advantage todaythe DC motors, and wound rotor motors.


Whether vfd is suitable for slip ring motors?

400hp slipring motor has been short circuited and connected to the 315kw variable frequency drive. The vfd has run continuously for 2 days without any problem.After a supply break the vfd couldnot resume but indicating a message of impedence short.


Can you connect a 3 phase motor to a 1 phase supply?

Single phase to three phaseThe physical internal windings between single phase and three phase motors makes this an impossibility That being said money can make anything happen. Depending on the amount of money you want to spend to make this happen there is a device on the market called a VFD ( Variable Frequency Drive). On the three phase input terminals you apply your single phase voltage. On the output terminals you connect your three phase motor. When run in this configuration there is an internal switch that has to be changed to let the VFD know that it should be looking for only two lines on the input to be hot. Other wise the VFD thinks that there is a line loss on the three phase input terminals and the unit will not start.Some 3 phase motor speed controllers can be run off a single phase supply, this caused us a problem at work when a new speed control was fitted to some laundry equipment, as we then had to rewire the supply to bring in a nuetral, so i suggest a speed controller is probably the solution.


How do you connected 3 phase motor to single phase power?

Use VFD to make 3 phase from single phase source.


Is there another way to reverse star delta motor other then swaping two phases over?

If the motor is connected to a VFD the conductors of the motor need not be changed. The phase reversal can be done with the VFD's internal circuitry.


What can we do to change 3 phase motor into single phase?

To convert a 3-phase motor into a single-phase motor, you would need to use a phase converter or a variable frequency drive (VFD). Both devices can help convert the single-phase power supply into a simulated three-phase output to run the motor. It's important to follow safety guidelines and consult with a professional to ensure proper installation and compatibility.


Can you use a 460 volt 3 phase appliance in a residential single phase set up?

3-Phase service is not generally available in residential areas. You could get a VFD to change the voltage from single phase to three phase. VFD (Variable Frequency Drive) Look up Drives Warehouse. They have all kinds of VFD's like this model: SJ200-015NFU2


How you can connect three single phase transformers as a three phase transformer Y to Y?

You can not unless the installation is a motor and cost is not important. Depending on the amount of money you want to spend to make this happen there is a device on the market called a VFD ( Variable Frequency Drive). On the three phase input terminals you apply your single phase voltage. On the output terminals you connect your three phase motor. When run in this configuration there is an internal switch that has to be changed to let the VFD know that it should be looking for only two lines on the input to be hot. Other wise the VFD thinks that there is a line loss on the three phase input terminals and the unit will not start.


Did VFD exist?

Yes because VFD means Volunteer Fire Department and there are many characters in it


How do you install a timer to a VFD?

You can either use the inbuild timer in VFD or go with secondary timer or a controller like PLC. You may use the below link to learn more on VFD www-dot-smeclabs-dot-com