0
Its a very difficult subject to which most of my fellow designers estimate the ripple current in the caps and then select capacitors that can handle that current. The idea of voltage droop om most DC links can be forgotten because of other compensators such as a lower BEMF motor. The problem is to get as much life out of the caps as you can and that's to keep them cool as you can. Assume that every amp delivered from the DC like is an amp of ripple current and you should be OK.
Add your answer:
Earn +20 pts
Does a capacitor block ac current dc current or both?
No you can't use DC capacitors in Ac because in DC current , the current flows directly while in AC current, the current flows curved zig-zag. Thus Dc equipment can't mingle with AC as they need Direct flow. So DC capacitors can't be used for AC current...................AnswerMost capacitors will operate on either DC or AC. The exception is the polarised-type capacitor, which is designed to operate with a DC or an appropriately-biased supply.Often, a capacitor's rated voltages is specified in terms of DC -for example, '100 V (DC)', so care must be exercised if it is to be used with AC. This is because we always measure AC voltages as root-mean-square (rms) values, not as peak values. For example, '100 V (AC)' actually peaks at 141 V*. So, applying 100 V (AC) to a capacitor rated at 100 V (DC) may cause its dielectric to fail. In this example, the maximum allowable AC voltage must be 70.7 V, which peaks at 100 V.(*To explain: Vrms = 0.707 Vmax )
500 volts rms is equivalent to what dc voltage level?
it will be no DC not unless diodes and capacitors are applied. rephrase the question
What electric device smooths the pulsed DC to a smoother DC?
In power supplies both coils and capacitors are used to smooth the pulsing DC output.
Why do you use a dc capacitor in table fans while an ac capacitor in a ceiling fan?
there is no separate capacitors for AC and DC. All capacitors are same. Electrolytic capacitors are manufactured by creating a die-electric by chemical etching or electroplating on one plate. Such capacitors when connected in AC circuit dislodges the die-electric material and thus results in short circuit between the two parallel plates of the capacitor. For AC circuits only non-electrolytic capacitors should be used. The common type is oil impregnated paper capacitor.
What is the formula to calculate beta DC?
beta dc= ic/ib!!
How do you calculate total energy for a circuit that has three capacitors(10µF 15µF and 30µf) and a 20v dc supply?
Energy = (Capacitance*(Voltage)^2)/2. Three capacitors are there. Are they in series or in parallel. It is not mentioned. So friend has given only the formula as guidelines.
How are the capacitors treated in the dc equivalent circuit of an amplifier?
In dc equivalent circuit of an amplifier all capacitors are replaced by open circuit because capacitor block dc. As , Xc=1/2πfC We know that that frequency of dc is zero so Xc will infinite so we replace all capacitors with open circuit.
Why coupling capacitor block DC in amplifier?
capacitors at input block dc and allows ac only. so absolute none of the dc enters the circuit. They are called decoupling capacitors or blocking caps. -DANNY S
Does a capacitor block ac current dc current or both?
No you can't use DC capacitors in Ac because in DC current , the current flows directly while in AC current, the current flows curved zig-zag. Thus Dc equipment can't mingle with AC as they need Direct flow. So DC capacitors can't be used for AC current...................AnswerMost capacitors will operate on either DC or AC. The exception is the polarised-type capacitor, which is designed to operate with a DC or an appropriately-biased supply.Often, a capacitor's rated voltages is specified in terms of DC -for example, '100 V (DC)', so care must be exercised if it is to be used with AC. This is because we always measure AC voltages as root-mean-square (rms) values, not as peak values. For example, '100 V (AC)' actually peaks at 141 V*. So, applying 100 V (AC) to a capacitor rated at 100 V (DC) may cause its dielectric to fail. In this example, the maximum allowable AC voltage must be 70.7 V, which peaks at 100 V.(*To explain: Vrms = 0.707 Vmax )
What is the function of input and output coupling capacitors CC1 and CC2?
We don't know much about the circuit these capacitors are in, but they are coupling capacitors. Coupling capacitors isolate DC between stages or circuits, and they couple AC between those circuits or stages. Only the signal gets in and goes out. The DC the stage operates on is isolated from stage to stage.
500 volts rms is equivalent to what dc voltage level?
it will be no DC not unless diodes and capacitors are applied. rephrase the question
What electric device smooths the pulsed DC to a smoother DC?
In power supplies both coils and capacitors are used to smooth the pulsing DC output.
What is the function of a capacitors shortly?
*to store charge. *to smooth out(reduce ripple on dc) a voltage
What is DC coupled amplifier?
A: DC couple amplifiers refers to stages of amplifiers where is the biasing is direct without adding capacitors to remove the DC component from amplifier to amplifier
Why do you use a dc capacitor in table fans while an ac capacitor in a ceiling fan?
there is no separate capacitors for AC and DC. All capacitors are same. Electrolytic capacitors are manufactured by creating a die-electric by chemical etching or electroplating on one plate. Such capacitors when connected in AC circuit dislodges the die-electric material and thus results in short circuit between the two parallel plates of the capacitor. For AC circuits only non-electrolytic capacitors should be used. The common type is oil impregnated paper capacitor.
How do you convert an RMS current value to a DC value?
RMS current is converted to DC current by using a rectifier. Capacitors and other components are used to make a cleaner DC output with less ripple.
Why don't capacitors allow DC current to pass?
A capacitor allows AC (to pass through) because capacitors resist a change in voltage.. The capacitor need change resist in Input signal
