0
Add your answer:
Earn +20 pts
Why not to overload a socket?
Yes! A socket is a part of a circuit. Usually there are a number of sockets and lights associated with a specific circuit. The wiring of the circuit and the circuit breaker are limited to a specific amperage. If you exceed the amperage, you can blow the breaker. If the wire is rated for 15 amps and the circuit breaker is rated for 20 amps, the wires can overheat and cause fires.
How do you build a series circuit in your home?
You do not build a series circuit in your home. The only series circuits are the circuits that go through circuit breakers, light switches, and relays. Electrical and electronic devices use internal series circuits but those are the only ones people build. No one builds series circuits for house wiring. Electrical outlets are connected with parallel wiring.
WhVuvbreutpirhete iuat types of parallel circuits are there?
There is one type of parallel circuit. An example of this type of circuit is the electrical wiring in a house. These circuits are generally very complex and have a single power source.
What is it called when a circuit has gaps or breaks?
It is called an open, incomplete, or broken circuit. Circuits might be opened intentionally (using a switch), or unintentionally (breaks in, or disconnected wiring).
What is the proper ampere rating of circuit breaker for electric arc welder?
The proper ampere rating of a circuit breaker for an electric arc welder depends on the arc welder. Each is different. Look at the nameplate on the arc welder and choose the circuit breaker and wiring accordingly.
What is the difference between a run and a circuit?
run in a electrical system means a wiring & conduit runs coming from Panel Board Circuit Breaker to its branch circuit loads in a circuit. while circuit is a designated number of branch breaker in a panel board where power load was individual connected.
What is the exception to the minimum branch-circuit wire size that can be installed in a dwelling?
The exception to the minimum branch-circuit wire size that can be installed in a dwelling is for load centers in dwelling units where the branch circuits supply 15-amp or 20-amp receptacle outlets and are protected by a 20-ampere overcurrent device.
How do i find if wiring circuit is broken?
A multimeter will help you find if the wiring circuit is broken.
What is the Minimum branch circuit wire size in a dwelling?
The minimum size home wiring is #14 AWG, the rating for that size wire is 15 amps.
What happens if the switch is open in a parallel circuit?
If the switch in a parallel circuit is open, it breaks the circuit and interrupts the flow of current for that particular branch. The other branches in the parallel circuit remain unaffected and continue to operate independently.
Does the code permit the ampacity of switch legs to be less than the ampere rating of the branch circuit?
No, and here's why: the rating of the branch, determined by the overcurrent protection, is designed for the ampacity of the branch conductors so that they breaker trips before the conductors heat up enough to start a fire. If you put in smaller wires on the same branch, they will get MUCH hotter before the circuit breaker trips, if it ever does. For example, a 20A branch, protecting 12AWG wiring; add some 14 AWG rated for 15A. Something faults the switched leg at 18A; enough to burn out the wiring but not enough to trip the breaker. House burns down, insurance doesn't pay because of "faulty wiring" installed negligently by a person without proper training and credentials.
What is the minimum branch-circuit wire size installed in a dwelling?
The minimum size home wiring is #14 AWG, the rating for that size wire is 15 amps.
What has the author William J Meese written?
William J. Meese has written: 'Analysis of current technology on electrical connections in residential branch circuit wiring' -- subject(s): Electric connectors, Interior Electric wiring
Is the circuit wiring between the motor starter in a motor control center going to the equipment disconnect with a circuit breaker in it a feeder or a branch circuit?
The circuit wiring between the motor starter and the equipment disconnect with a circuit breaker in it is typically considered a feeder. This is because it carries power from the electrical distribution panel to the equipment disconnect, providing power to multiple branch circuits.
Is it within code to hard wire a fluorescant light fixture into a 20 amp branch circuit that is now designated for general use utility receptacles?
It is not good practice in new wiring, but done all the time as part of a retrofit. Use 12 AWG wiring and make sure the circuit is not overloaded.
What causes the main breaker to trip from a fault current from a twenty amp branch circuit?
A fault current on a twenty amp branch circuit can cause the main breaker to trip due to the higher-than-normal flow of electricity, which exceeds the circuit's capacity. This could be caused by a short circuit (abnormal connection between conductors) or a ground fault (unintended connection between a conductor and ground). The main breaker detects this overload and trips to prevent overheating and potential fire hazards.
Can an astable multivibrator replace household wiring if the circuit is modified?
No. Household wiring requires household wiring.
