answersLogoWhite

0


Best Answer

It is used to transfer torque between two parallel but not collinear shafts.

Depending upon the matterial of the 3 discs , oldham coupling can be used in many devices. They can easily be used in servo mechanisms.

User Avatar

Wiki User

16y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

15y ago

Application of Oldhams coupling

It was basically invented to connect two parallel non co axial shafts.

It is a really good mechanism and transmits the same speed and same direction of rotation.

It is not of much importance now as gears are being used.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Applications of oldhams coupling
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

What are the types of coupling in software engineering?

control coupling content coupling common coupling data coupling external coupling message coupling


What is a Thompson coupling?

A Thompson Coupling is a High RPM, High angle, constant velocity joint between to turning shafts. The TC is used in a wide range of applications from the automotive industry, trains and on the rotor shaft of helicopters.


What are types of mechanical coupling?

There are many like flexible coupling, jaw coupling, sleeve coupling, tire coupling, pin and bush coupling, rigid coupling, etc


Why transformer coupled amplifier is more efficient than RC coupled amplifier?

an RC coupled amplifier is basically used for voltage amplification , where the circuit currents are quite low. higher currents & voltages would mean more dissipation in the load resistors , which is essentially very lossy . The coupling amplitude to the next stage is ideally the same as the previous stage signal excursion. However if a transformer is used for coupling , both large voltages & current can be handled without incurring the dissipation of a resistive load. Moreover a coupling gain of the transformer primary to secondary ratio is also a bonus. also because of the possiblity of correct impedance matching on the primary & secondary side maximum power coupling is obtained. hence transformer coupling is more efficient in such applications. in high frequency applications transformer coupling , along with tuned circuits as applicable is the choice circuit.


Which coupling gives high gain in case of amplifier?

no.transformer coupling gives higher gain

Related questions

What are the types of coupling in software engineering?

control coupling content coupling common coupling data coupling external coupling message coupling


What is a Thompson coupling?

A Thompson Coupling is a High RPM, High angle, constant velocity joint between to turning shafts. The TC is used in a wide range of applications from the automotive industry, trains and on the rotor shaft of helicopters.


What are types of mechanical coupling?

There are many like flexible coupling, jaw coupling, sleeve coupling, tire coupling, pin and bush coupling, rigid coupling, etc


What are the applications of slider crank mechanisms?

The applications of a slider crank mechanism is a Reciprocating engine, Rotary engine, Oscillating cylinder engine, Hand Pump, Scotch Yoke, Oldham's coupling, Elliptical Trammel


Which coupling gives the higher gain in case of amplifier - a Capacitor coupling b Impedance coupling c Transformer coupling?

transformer coupling


What is RC coupling?

rc coupling is a coupling that involves capacitor aand resistor


Why transformer coupled amplifier is more efficient than RC coupled amplifier?

an RC coupled amplifier is basically used for voltage amplification , where the circuit currents are quite low. higher currents & voltages would mean more dissipation in the load resistors , which is essentially very lossy . The coupling amplitude to the next stage is ideally the same as the previous stage signal excursion. However if a transformer is used for coupling , both large voltages & current can be handled without incurring the dissipation of a resistive load. Moreover a coupling gain of the transformer primary to secondary ratio is also a bonus. also because of the possiblity of correct impedance matching on the primary & secondary side maximum power coupling is obtained. hence transformer coupling is more efficient in such applications. in high frequency applications transformer coupling , along with tuned circuits as applicable is the choice circuit.


Which coupling gives high gain in case of amplifier?

no.transformer coupling gives higher gain


Which Coupling produces minimum interference with frequency response?

Direct coupling


What is practical applications of Flange coupling and where it is used?

It is used on the exhaust of many vehicles. It give a place for some adjustment or for parts such as a catalytic converter that may need to be replaced.


Applications of Slider-crank mechanism?

• Reciprocating engine • Rotary engine • Oscillating cylinder engine • Hand Pump • Scotch Yoke • Oldham's coupling • Elliptical Trammel


What are the different types of couplings?

1)rc coupling 2)transformer coupling 3)direct coupling