0
If the circuit is carrying current then that means that the load (resistance) is in the circuit. if an ohm meter is connected in the live circuit then there would be some voltage drop at the ohm meter but as the meter has very less resistance, this would damage the instrument.
Add your answer:
Earn +20 pts
When an ammeter is connected to measure current circuit current will decrease sightly because R total decreases after the meter is inserted?
Current will be decreased because of the resistance of the ammeter added to the circuit's resistance. In other words total resistance increases.
How do you find resistance when you have current and resistance total?
If you are looking for the resistance of each resistor in either a series circuit or a parallel circuit you must measure the current I and the voltage V for each resistor. Then calculate its resistance using Ohms Law R = V / I where I = current (Amps), V = voltage (Volts) and R= resistance (Ohms).
How could you calculate the resistance of a circuit?
A variety of techniques can be used. Node-Voltage and Mesh-current (or Loop-current) methods, for example. See related link for examples. If there is a single voltage source in the model, then find the current supplied, and Resistance = Voltage/Current. {R = V/I} You could simulate/ model the circuit on a computer then apply the power profile and a current value will be calculated. Or if you have the circuit working, Place an amp meter into the circuit and measure the current. V/i = resistance.
What is used to measure the current in a circuit and how is it connected?
To measure the current in the circuit an ammeter is used and it is connected in series
Where do you set the dial when you are measuring resistance on house current?
YOU DO NOT "measure resistance on house current".You never measure resistance of anything that has any path to any source ofpower ... not to a wall outlet, a battery, a windmill, a solar panel, etc. You onlymeasure resistance when all power is REMOVED from the circuit or componentyou're measuring. Then, the range you choose for the ohmmeter depends onthe component or circuit you're measuring, NOT on how it's powered when it'sturned on.
Why should you never measure resistance in a circuit carrying a current?
Ideally true, but seldom so. The vast majority of resistance meters use current to measure resistance and just use V=IR to give R - the resistor is in a circuit carrying current. The only method that does not have a current through the resistance, it actually relies on the fact, is a Wheatstone bridge. The most important reason for not having a current is that you will be using a current in most cases, to meaure the resistance. Current from another source will screw the reading. Also, with a current flowing, you are not measuring resistance - you are measuring impedance - a combination of inductance and resistance.
The number of ohms in a circuit is a measure of the?
resistance to the flow of electrical current in the circuit. It is a measure of how much opposition the circuit presents to the flow of electricity. The higher the number of ohms, the greater the resistance in the circuit.
How do you measure the resistance in a parallel circuit?
You have to measure the voltage, and the current. The resistance is then calculated by using Ohm's Law.
What are the 3 ways to measure electricity in circuit?
The three ways to measure electricity in a circuit are voltage, current, and resistance. Voltage is the measure of electrical potential difference between two points, current is the flow of electric charge in a circuit, and resistance is the opposition to the flow of current.
How do you measure alternating current voltage and resistance?
You measure current by inserting an amp meter in series with the circuit or using a clamp-on meter to measure current by induction. You measure voltage with a volt meter across the supply. You measure resistance in ohms across the resistance. Luckily all these functions are in the same meter in most cases.
When an ammeter is connected to measure current circuit current will decrease sightly because R total decreases after the meter is inserted?
Current will be decreased because of the resistance of the ammeter added to the circuit's resistance. In other words total resistance increases.
1 What is the effect caused by the ammeter resistance when an ammeter is inserted into a circuit to measure the current?
An ammeter has a finite resistance which is inserted in series with the rest of the circuit, increasing the total resistance and decreasing the current. A good ammeter has a very low resistance, so it shouldn't affect the circuit noticeably.
What are watts amps and ohms?
Watts measure power, or the rate at which energy is consumed or produced. Amps (amperes) measure electrical current, or the flow of electrons in a circuit. Ohms measure electrical resistance, or the opposition to the flow of current in a circuit.
How do you find resistance when you have current and resistance total?
If you are looking for the resistance of each resistor in either a series circuit or a parallel circuit you must measure the current I and the voltage V for each resistor. Then calculate its resistance using Ohms Law R = V / I where I = current (Amps), V = voltage (Volts) and R= resistance (Ohms).
What instrument measures electrical pressure in a circuit?
A multimeter is commonly used to measure electrical pressure in a circuit. It can measure voltage, current, and resistance, providing a comprehensive view of the electrical characteristics in the circuit.
What are applications of OHM METER?
It measures resistance in a component or circuit to determine if there is a break in that circuit or component. If there's no resistance, it means there's a break, as no electrical current is passing through.
What is the resistance if the current is 0?
If the current is 0, then the resistance does not matter since there is no flow of current. In this case, Ohm's Law (V = IR) is not applicable because there is no current to interact with the resistance.
