0
Why not hook ground to neutral since they are hooked on same spot in breaker box why not in outlet box.?
Wiki User
∙ 11y ago
The "hot" wire and the neutral wire both carry current (the same amount, in fact) when a load is connected to complete the circuit. The ground wire never carries current except when a fault-to-ground situation occurs. Yes, neutral and ground wires should both be at ground potential, but NO they should not be connected at the outlet.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Is the neutral wire on a 220v outlet the same as the ground?
No it is not
Why is the ground wire hot at all outlet boxes on a particular circuit?
Most likely the ground (green) wire is mistakenly connected to hot instead of the hot wire (black) at the breaker panel! Possibly you meant the neutral wire not the ground wire, in that case most likely the neutral (white) wire is mistakenly connected to hot instead of the hot wire (black) at the breaker panel! In either case check all three wires in the breaker panel for that circuit to make sure they are all correctly connected! Black is hot, White is neutral, Green (or uninsulated in some cases) is ground.
Is a ground fault indicator outlet installed at the breaker box?
There are tow places to put a Ground Fault Circuit Interrupter. There is a GFCI breaker which would be installed in a breaker box and a GFCI outlet that can be installed anywhere. Most GFCI outlets allow you to connect regular outlets to the GFCI and those outlets will also be protected.
What do the letters stand for on a 4 prong plug?
On a 240 volt outlet, such as a dryer outlet: G is Ground, W is Neutral, X and Y are the two Hot legs.
Can you ground a wall outlet by running a jumper wire from the neutral terminal to the ground screw?
Not correctly , It will show on a tester that it is grounded but you should run a separate ground for it to be properly grounded
How can you wire a 110V plug outlet from a 240V plug outlet not speaking of a converter but actually changing the plug outlet so that there are no long term effects on the 120V appliance?
Assuming the wiring to the outlet has 2 loads and one neutral, isolate one load from the outlet and use the neutral as the common. be sure to ground from the receptacle to your conduit or ground lead. You should also replace the corresponding breaker with a 120 volt single breaker.
When wiring a range the outlet has a neutral ground and 2 hots you have three wires do you put the bare wire in the neutral or ground on the outlet?
the bare copper is always a ground
Is the neutral wire on a 220v outlet the same as the ground?
No it is not
Why is the ground wire hot at all outlet boxes on a particular circuit?
Most likely the ground (green) wire is mistakenly connected to hot instead of the hot wire (black) at the breaker panel! Possibly you meant the neutral wire not the ground wire, in that case most likely the neutral (white) wire is mistakenly connected to hot instead of the hot wire (black) at the breaker panel! In either case check all three wires in the breaker panel for that circuit to make sure they are all correctly connected! Black is hot, White is neutral, Green (or uninsulated in some cases) is ground.
What is symptom of a circuit incorrectly wired?
Circuit breaker tripping, or non functioning outlet. The neutral and hot can be reversed, or an open ground, and you will have no symptoms. This can only be detected with a circuit tester you plug in to check the wiring.
Will an outlet fry if both hot and neutral are connected to silver terminals?
No, it will just trip the breaker as you have a dead short.
How do you wire a 220v connection into the main panel?
I assume you mean you are wiring a 220 volt circuit. You will install a 220 volt double pole breaker of the correct size for the circuit. An example would be for an electric dryer that requires a 30 amp double pole breaker wired with 10/3 wire. You connect the Red & Black wires to the breaker. One on each screw. You now connect the White wire to the neutral bus bar in the service panel. Then connect the bare copper ground wire to the ground bus bar in the service panel. At the dryer outlet connect the black & red to the hot screws, white to the neutral, and ground to ground. They will be labeled on the back of the outlet.
Is the inside of an outlet a conductor?
Inside an outlet there are conductors: hot, neutral, and sometimes ground. The rest of the inside of an outlet is insulator, to keep these conductors from shorting.
Is a ground fault indicator outlet installed at the breaker box?
There are tow places to put a Ground Fault Circuit Interrupter. There is a GFCI breaker which would be installed in a breaker box and a GFCI outlet that can be installed anywhere. Most GFCI outlets allow you to connect regular outlets to the GFCI and those outlets will also be protected.
How do you put on a four prong outlet on a roper electric dryer?
Black & Red are hot, and White is neutral. If it has no place to connect neutral connect neutral to ground.
Why would there be low voltage in your 110 volt outlet when the breaker is off?
Low voltage in a 110 volt outlet when the breaker is off could be attributed to a faulty wiring connection, loose or corroded terminals, or a problem with the outlet itself. It is recommended to have a licensed electrician inspect the outlet to identify and rectify the issue to ensure safe operation.
Arc-fault circuit interrupter trouble shootting?
The test is, push the button, if the breaker trips, tested ok, if not,the breaker is bad,(rare) or if it does not reset, somewhere in the house, hot is connecting to neutral. Bad outlet or even light fixture. Arc-fault are used in bedrooms. Codes in most areas. These are in case the kids stick a fork into an outlet. Ground fault is used near water.
